How to reprogram the alarm keychain? Programming remote control car alarms

To be able to easily manage the alarm system of your car, drivers use a command keychain. This is a radio transmitter that encodes information in a certain way. It is this code that perceives the control unit of the system and obeys the will of its owner.

For some reason, the driver of a car with an alarm system may need to change the form of the radio broadcast once. To do this, you need to learn how to reprogram the alarm keychain. Experienced auto mechanics are ready to give advice on how to solve this problem. For each version of the system, there is a technology for reprogramming the keychain.

When is reprogramming necessary?

Reprogramming the key fob may be required for several reasons. It happens, the driver buys a used car, in which the alarm has already been built in. The last owner transfers the key fobs to the new owner of this vehicle. But there is always a possibility that he still has one or two control panels at home.

To protect yourself from trouble, you need to reprogram the key chain. This is considered an unspoken rule that applies when buying a car with mileage.

There are also some failures that can cause the system to become out of sync and the system itself. If a dynamic code is applied to the alarm, when the button is pressed more than 30 times outside the transmission block, the remote can be disconnected from the program.

The binding can be carried out independently. This process is simple, but it has several features.

Preparation for work

Before you re-program the alarm keychain, you need to familiarize yourself with some of the features of the upcoming process. If the key fob has been lost, purchase the new device follows only the same model that was originally included with the alarm.

If the system is controlled by several radio transmitters, they are reprogrammed all at once. Otherwise, they can not be attached to the control unit afterwards.

Most suppliers of security systems necessarily put in the instruction manual. Complexities arise if it does not have a tab with the text in Russian or is written with the assumption of many errors (especially if the device is made by China or Korea).

First of all, the car owner should look into this manual. It should show schematically the device of the panel, the signal receiving unit, etc. If, for some reason, the manual is not available, you can try to follow the generally accepted instruction.

Programming mode

любой системы начинается с поисков кнопки Valet или Overread. Customizing the keyfob of any system begins with the search for a button Valet or Overread. Sometimes it is not easy to find it. At this point, the original manufacturer's instructions come in handy. If it's not there, you'll have to search yourself.

This button is a switch. To the driver accidentally did not press it, the button is usually located in a place hidden from prying eyes. But there is always an opportunity to get to it. Most manufacturers of security systems leave this switch in the fuse box, which is located inside the cabin.

Owners of cars should look under the panel with the inscription Fuse. The cover needs to be removed. Next, the opened space is examined for the presence of a switch. It happens that the buttons are not here.

Then you need to explore all the places under the steering column, the instrument panel. In this case, it is necessary to check carefully all the removable plugs. Next, you need to pay attention to the glove box. In some cases, the button may not be installed at all. It can also be located next to the control unit of the alarm system. In these cases it will be necessary to resort to the help of a professional auto mechanic. If the button has not been provided by the system, its function can be performed by the ignition switch.

Basic programming technology

When studying the question of how to tie a key chain to a signaling, one should consider the basic principle of performing this process. After the switch button is found, the system is switched to the service control mode (Valet mode). This allows you to set new functions, perform maintenance and forcibly turn off alarms. Keyrings are also attached to the system in this mode.

However, it is not so easy to set the programming mode. To do this, you need to know the special combination of pressing the switch. This is a certain security code that is needed to enhance the safety of using the car. It is prescribed by the manufacturer in the instructions. If, for some reason, the code has been changed, only a professional in the technical service can restore it.

If the code is approached, you can start programming. Usually, the kit can include up to 4 trinkets, which the car is subject to. The alarm will work correctly if all consoles are attached to it simultaneously.

To make the process easier, assign numbers to each button on the remote control. "1" - activation of the guard; "2" - withdrawal of protection; "3" - channel ch2; "4" - channel ch3; «5» - adjustment of signals of a keychain.

Keychains system Sheriff

To understand how to tie a key ring to a Sheriff alarm, you need to read the instructions. First of all, the driver turns off the alarm and sits in the car, closes the door, turns on the ignition.

Then press the Valet button three times. After a single signal sounds, the control unit enters the programming mode. Each operation should be performed no longer than 5 seconds. Otherwise, the system will exit the programming mode (a short and then a long beep will sound). If you turn off the ignition, the same thing will happen.

If you repeat three button presses, the alarm will emit several short and one long beeps. On the first key fob, the "1" button is held. When a long signal sounds, reprogramming has occurred. All other key fobs are subjected to the same procedure. Then you can exit the setup mode (wait 5 seconds).

Change the secret code in the Sheriff system

, следует рассмотреть процедуру изменения секретного кода. Studying how to reprogram the alarm keychain , you should consider the procedure for changing the secret code. To do this, the security system is turned off. Then enter the secret code using the button Valet. Ignition is turned on, off and on again. Then, using the same button, set the first digit of the encoding. Then the ignition switches off again and turns on. Then the second digit is entered. The procedure is repeated. The audio signal will notify you of the correct encoding.

After the above manipulations with the triple click on the settings lever you need to enter the service mode. The alarm will emit a few short and one long beep.

On the first keyfob, press the "1" button. The buzzer will notify you of successful manipulation. This scheme connects all other transmitters to the signaling.

Starline key fobs

If the Starline A91 alarm system is installed in the car, reprogramming is quite simple. To do this, the alarm is turned off. The hidden button for entering the settings must be pressed 7 times. Only after this the ignition is switched on.

If the setting mode is activated, the siren will emit 7 beeps, and the backlight will appear on the remote control. Then you can reprogram the Starline car alarm stick . At the same time, the "1", "2" buttons are clamped. There will be one beep. Then the subsequent consoles are programmed in the same way.

The exit from the setting mode occurs automatically after 10 seconds. Inaction. In this case, 5 flashes of parking lights will occur.

Programming Starline Twage A6, A8, A9

The programming of the popular Starline A91 signaling model is simple. But it should be borne in mind that the presented brand has a whole line of security systems of the Twage series.

To reprogram the keyfobs for the Starline Twag A6, A8, A9, it is necessary to turn the ignition. The button for entering settings is clamped for 6 seconds. Then 4 beeps will sound.

To tie the key chain to the display, the "1" and "2" buttons are pressed together. This procedure is similar to the previous settings. For an additional console without an LCD display, you must press the "3" and "4" buttons. The number of rings corresponds to the number of the remote control.

When all the key chains are recorded, the ignition is turned off. Further, in the absence of any action, the adjustment mode closes after 6 seconds. The parking lights will light 5 times.

Tomahawk System

Tomahawk может быть записан довольно просто. The Tomahawk keychain can be recorded quite simply. In the delivery set they can be up to 4 pieces. To make the binding, turn the ignition (the engine does not turn on). The setting button is held down until 4 siren sounds. The lever is released.

Simultaneously, the audio control buttons on the remote control and the trunk opening are pressed. Keep them in this position until a signal sounds. For the first keyfob, the dial tone will be followed by one, and for the second transmitter - two (and so on). Tomahawk запомнит код, систему оставляют бездействовать в течение 5 с. When each keychain Tomahawk remembers the code, the system is left idle for 5 seconds.

Signaling "Sherkhan"

необходимо воспользоваться одним из 2 основных способов. To program the "Sherkhan" signaling keychain, you must use one of 2 main methods. The first approach does not apply the pin code. Within 4 s. It is necessary to switch the ignition on and off. If the dimensions flicker, the input to the settings is executed.

Immediately you need to press the button of the first key fob. Dimensions flashed 1 time. The same happens with other consoles. To exit the setting mode, wait 4 seconds. After that all the key chains attached to the control unit will function. The remaining devices to control the work of the car can no longer.

Settings with pin code

The second version of the Sherkhan system can use the pin code. For this, when the ignition is switched on for 4 s. The first digit of the code is entered. When the dimensions flicker, the second digit is also entered. Then the button on the remote control is clamped. Then the procedure is carried out in accordance with the previous method. To exit the service mode, wait 4 seconds.

, можно в любых ситуациях выполнить процедуру быстро. Knowing how to reprogram the alarm keychain , you can perform the procedure quickly in all situations. Especially often in low-cost systems failures occur. In order to quickly restore the connection between the keyfob and the control unit, it is necessary to know the communication technology of the control panels with the alarm system.