HomelinessBuilding

Nanoisol B vapor barrier: instruction manual

"Nanoisol B", the instruction for use of which should be studied by you after the purchase, is a modern vapor barrier material consisting of a two-layer polypropylene film. It is capable of retaining condensate on the surface and promoting its evaporation. This material is designed to protect the insulation and roofing, as well as other building structures from the effects of water vapor, which can penetrate from the interior.

Scope of use

"Nanoisol B", the instruction on which application will help you to exclude mistakes, is laid down for thermal insulation, so that steam and condensate can not seep. The heat insulation, thus, turns out to be protected from moisture. This is especially true in winter, when the difference in temperature outside and inside the building is able to form a condensate. Use this material can be used to insulate floors between floors, as well as load-bearing walls. Polymer film will exclude the possibility of particles of insulating materials getting inside the room.

Instructions for use

"Nanoisole B", the instruction for use of which will help you with the work, is used in insulated pitched roofs of attics with any type of roofing. To cover this vapor barrier is necessary on the supporting frame or on the black plating for thermal insulation. If you want to use "Nanoisol B" for insulation of walls of low-rise buildings, then this material can be used for internal and external work. The material should be installed on the frame from the inside of the insulating layer.

If it is a question of interfloor overlapping, the laying is carried out on the slabs of the floor or the rough floor. In the first case, it is necessary to cover the vapor barrier between the lags, which are represented by the floor beams . The vapor barrier must be on top and bottom of the insulation layer, so it will protect the material from both sides.

Using a vapor barrier "Nanoisol B" in conjunction with laminated parquet floors

Sometimes "Nanoisol B", the instruction for use of which is described in the article, is used in the arrangement of laminated or parquet floors. In this case, the two-layer polymer film must be laid directly on the cement screed, while the finish coat is laid on top.

Recommendations for the installation of insulation "Nanoisol B"

If you decide to use the material described above as a vapor barrier layer together with a heater in the area of the roof or supporting walls, the material must be located on the inside of the thermal insulation, and it should fit snugly on the smooth side. The layer is fastened to the lathing or roughing with a construction stapler. Among other things, zinc-coated nails can be used to fix the film, which are driven into the frame.

Steam insulation "Nanoisol B", the instruction for use of which will help you with the work, should be laid horizontally with the formation of an overlap, the width of which can reach a limit of 10 to 15 cm. The laying on the wall or pitched roof is carried from the bottom up. In order to protect the insulation film from damage, experts advise the use of under-roof seals.

Features of the use of the vapor barrier "Nanoizol D"

This material is a polypropylene fabric, which is coated on one side with a polymer film. With it, you can protect the unheated pitched roofs. If we are talking about a warmed flat roof, then "Nanoizol D", one side of which is covered with laminated polypropylene film, will act as a vapor barrier. If you are engaged in arranging the screed in the basement floor, then this material can perform the functions of waterproofing.

"Nanoisol D" does its job well with its tasks in the installation of the floor, which will be operated in a room with high humidity, here you can include a socle. "Nanoizol D", the instruction on which application will help you avoid mistakes, when setting up pitched roofs, it is laid on top of the battens or flooring, and then fixed with a construction stapler. An alternative option of fixing is the laying of the panel on the flooring or crate, where the material should be faced with a smooth side up. It is necessary to start work from the bottom edge of the roof, and to ensure a more reliable waterproofing, you should fix the panels together with a connecting tape.

Cement screed on insulated floors is poured over the material, as well as the layer of thermal insulation. At the edges, the water vapor barrier must be raised about 15 cm high on the adjacent walls.

Tips for using Nanoisole FS

On sale you can also find "Nanoisol FS", the instruction for the use of this material will be presented below. This vapor barrier is designed to protect roofing and wall structures, as well as ceilings.

"Nanoisol FS" is a vapor-tight three-layer membrane that differs from "Nanoisol B" by the presence of an additional layer of processed lavsan. It has a mirror effect and is necessary for reflecting infrared radiation. Thus, the manufacturer has achieved additional heat savings. Steam insulation is installed from the inside of the roof or wall to the elements of the supporting frame, be it rafters, beams or racks.

It is possible to mount under the roughing, using staples of a construction stapler or galvanized nails for fixation. If you have to work with a block or brick wall, which need to install a vapor barrier, then you can use a connecting tape of the same manufacturer for fixing.

Conclusion

Now you know what "Nanoisole B" is. Instructions for use, which side to install this material - everything was mentioned above. Now you only have to decide what kind of vapor barrier to purchase for carrying out this or that kind of work.

Similar articles

 

 

 

 

Trending Now

 

 

 

 

Newest

Copyright © 2018 en.birmiss.com. Theme powered by WordPress.