How to make a hole in your belt with your own hands?

How to make a hole on your belt? Inaccurate performance of the work in this case is able to completely ruin the appearance of the product. Therefore, before embarking on the task, it is necessary to understand how to properly punch a hole, what tools are required for this. Next, consider a few recommendations that will help you figure out how to make a hole in the belt.

Application of a special punch

How to make a hole as neat as possible in a belt? This will help the piercer for the skin. To buy such a device can be relatively inexpensive at any point on the sale of tools for needlework. In order not to make a mistake with the diameter of the punch, going for his purchase, it is necessary to take the belt with him. If you need to make holes in several belts, you should purchase a tool with removable tips of various sizes.

In preparation for work, it is necessary to mark the plane of the belt by measuring the distance between the factory holes with a ruler. Then it is necessary to postpone the same segment on the plane and mark the place of the future hole.

Before applying a hole punch for the skin, it is necessary to fix the strap so that its plane is in tension. Further, it is sufficient to apply the point of the punch to the target area and strongly squeeze its arms. Relax puncher for the skin is necessary, as soon as its elements completely sew the material.

Nails and a hammer

How to make a hole in a leather belt? The simplest solution here is the penetration of the hole with a nail. The main thing is to initially determine the location of the future hole by performing the appropriate measurements. To make notes in the right places, it is enough to use a ballpoint pen or marker.

The work is done in the following order:

• A suitable nail is chosen, the diameter of which should approximately correspond to the dimensions of the factory holes on the product;
• The belt is located on a flat board surface;
• The point of the nail is set at the previously planned point;
• A few accented strokes on the nail cap are performed until the belt is fully sewn by the belt;
• The nail rotates several times in the thickness of the leather product, after which it is carefully extracted outward with the help of pliers.

At the end of the work, it is advisable to treat the edges of the resulting hole with shoe cream with a neutral shade. Thus, it is possible to smooth the uneven edges of the material at the breakdown point.

Electric drill

Thinking about how to make a hole in a belt, it is worth considering the option of using an electric drill. With care, with its help you can make fairly even, neat holes.

To begin with, it is recommended to fix the belt, pressing down its ends with a heavy load. In this case, the area to be treated must be located on a flat, hard surface, for example, a wooden bar.

To determine the optimal drill size, it is enough to manually insert several rods of individual diameters into the already existing holes on the belt. It is recommended to stop on a drill that will fit tight enough into the hole.

How to make a neat hole in the belt with a drill? To do this, you must first make a slight groove at the intended point, using the tip of an acute knife. As a result, the drill will not jump to the sides during the execution of the work.

Starting to make a hole, it is necessary to make short-term starts of the mechanism of the drill. Thus, the risk of a sloppy hole can be minimized.

Shoe Wool

To cope with the task using a shoe silk, first you need to mark the plane of the belt. Next, place the product on a sufficiently hard plane, which at the same time can pierce the tip of the instrument. You can lay the belt on the compacted soil or a piece of foam.

Next, you need to make a hole in the belt with the tip of the awl. If necessary, it is necessary to expand the diameter of the hole by any suitable metal rod. Pieces of material that formed on the underside of the product after penetration, can be carefully trimmed with manicure scissors.

Helpful hints and cautions

There are several recommendations, the adherence to which will make it easier to avoid injuries:

1. Trying to find a solution, like in a belt to make a hole, do not resort to using a conventional kitchen knife or scissors. Use of such blades will not allow creating accurate holes.
2. Puncturing the coarse skin can be quite a challenge. Therefore, when using a punch, you may need to use the help of a partner.
3. The use of improvised tools, such as a hammer and nails, awl or drill, will not require additional costs. However, the operation of a special tool designed for such work will save not only time, but also reduce the risk of accidental injuries.
4. Before you start to break holes in a leather product in one way or another, it may be worthwhile pre-training using a piece of old, unnecessary material.

Let's sum up the results

So we found out how to make a hole in the belt. The solutions indicated in the presented material will not force you to ask for help in the workshop. The main thing is to do the work slowly and as accurately as possible so as not to spoil the product.