HomelinessTools and equipment

Gilex Jumbo Pump Station: overview, specifications, features and reviews

The Jilex Jumbo pump station is superficial. The equipment has a built-in ejector, which is connected to the pipes. The system promotes efficient absorption of liquid at the inlet, in addition, the equipment does not require a clean fluid and dissolved gases.

Reviews about the features of models of pumps "Jumbo"

Pumping stations "Gileks", which you can read about below, are represented by models 60/35 П and 70/50 П, which have a polymeric body, and the threaded screw parts are made of brass. Pumps 60/35 N, 60/45 and 70/50 have a body made of stainless steel, whereas in the 60/35 model this part is made of cast iron. According to users, some parts, including the impeller, are made of plastic materials, they are highly wear-resistant.

The Gileks pump station, whose malfunctions can be eliminated by you, has a transitional aluminum flange, a closed lid, which is why its contact with water is completely excluded. Customers emphasize that the equipment is well protected against leaks, this is provided by the use of graphite ceramic seals.

The device operates due to an electric motor, which is a short-circuited system with component parts. The stator is located under the protection of the thermal protector, the latter assumes the function of an emergency interlock. As the buyers emphasize, this component turns off the engine if the winding overheats. The Gileks pumping station is capable of maintaining the required pressure, switching off and on, depending on the fluid flow. The units can be divided according to the principle of control. Some of them are based on the principle of automation, they have a surface accumulator, a pressure switch and a manometer. The volume of the accumulator in this case is 24 liters. If we are talking about a pump brand 70/50 P-50, then this figure is 2 times more, since there is a horizontal accumulator with a volume of 50 liters. Model 70/50 H-50 HOUSE is equipped with a powerful controller that guarantees efficient control.

Review of positive qualities

The Gileks pump station has many advantages, among them there are:

  • Reduction of inrush currents;
  • Minimization of mechanical loads;
  • The absence of a hydraulic shock at the moment of switching on.

It should be noted and reliable protection against voltage drops, as well as the absence of dry running. A certain pressure is set in the pump and maintained during operation at the specified elevation. The dry running is eliminated thanks to the automatic control unit, which controls the amount of flow. Here the threshold value of the pressure is laid.

Characteristics of the "60/35 N-24" pump

This pump station "Gileks" is intended for surface installation, as an additional function is increased pressure. The maximum head is 30 m, and the throughput is equivalent to 3.3 m 3 / h. The power consumption of the device is 600 W, the water at suction should be clean, the size of the filtered particles is equal to 0.8 mm. The permissible liquid temperature can vary from 1 to 50 ° C.

The equipment is supplied with a built-in ejector, which is supplied as a unit in a single copy. The tank has a volume equal to 24 liters, as for the diameter of the outlet, this parameter is 1 inch. The power cord provides convenient operation of the pump, its length is 1.5 m. The pump must be installed horizontally. The permissible ambient temperature is 1 ° C or higher. You can not be afraid of the fact that this pump station "Jilex Jumbo" overheats, because the system has protection.

Characteristics of the pump "60/35 P-24"

This model has a maximum head of 35 m. The throughput is 3.6 m 3 / h. The equipment operates from 220/230 V. The power consumption is 600 W. The diameter of the equipment outlet is 1 inch. The ambient temperature during operation of the device can vary from 1 to 35 ° C. The control of the water level is electronic automatic.

Overview of the 70/50 P pump

This pump station "Gilex Jambo" costs 7500 rubles. And is intended for use in a garden. The equipment must be installed on the surface. The device combines the advantages of a centrifugal pump and the practicality of a self-priming model. The unit is adapted to operating conditions in Russia, where voltage fluctuations are frequent. In this case, the quality of the intake water can be different, in addition, it can contain a certain volume of gas. This equipment is intended for water supply from reservoirs, wells, wells, reservoirs and tanks.

70/50 Technical Specifications

If you are interested in pumping stations "Gilex Jambo", it is recommended to read reviews about them before going shopping. The model 70/50 П, whose power consumption is 1100 W, is no exception. This garden pump has a capacity that is 3.9 thousand l / h. The maximum suction depth is 9 m, but the water supply height is 45 m. The device weighs 9.85 kg. The equipment has an automatic system that provides self-switching on and off, and the pressure will be maintained at a certain level. This ensures a continuous mode of operation.

The pump can be operated with a wide range of temperatures, but the temperature of the pumped water can range from 1 to 50 ° C. These pumping stations "Gilex Jambo", reviews about which are often quite positive, have an asynchronous short-circuited engine, a manometer and a hydraulic accumulator. The use of graphite ceramic seals eliminates leakage from the pump. In the process of manufacturing materials are used according to the type of glass-filled polypropylene, which forms the basis of the shell. The threaded parts are made of brass, but the wheels are made of plastic material. The Venturi guide tube provides productive and stable operation for a long service life.

Features of repair

Despite the fact that the described equipment is of high quality, it may be necessary to repair the pump station "Gileks". If you notice that there is a rumble in the engine, and the equipment chokes, all this can cause problems with the impeller or the engine. Disassemble the device and inspect it yourself. If the impeller cracked or the bearings fail, they can be replaced with new ones and assembled in the reverse order.

Similar articles

 

 

 

 

Trending Now

 

 

 

 

Newest

Copyright © 2018 en.birmiss.com. Theme powered by WordPress.