Installation of plastic skirting with your own hands: instructions, installation features and recommendations

As you probably already had time to notice, in the process of repairing and arranging rooms of insignificant details can not be. In addition, even insignificant elements sometimes play a key role in creating a complete picture. And here it is impossible to decide: the skirting board or the floor covering is more important, all these components make it possible to form a harmonious picture. If you decide to fix the skirting boards, you should familiarize yourself with the basic technologies, one of which is most likely to suit you.

Bonding of plinth

Installation of plastic skirting can be carried out with the help of glue. This method is the most common, and use in the process of this can be different types of compounds, including liquid nails. The advantage of this technique is the lack of drilling. As a result, dust will not form, and the work will not seem dirty. It is not necessary to hurry to glue the baseboard, at the first stage it is necessary to reconcile everything, and after installing the elements without glue. After all the components are adjusted, and also approximated, the elements can be installed in their places. As a disadvantage of this method is a one-time use of the plinth, its repeated use will be impossible, and dismantling will worsen its appearance. Among other things, there is a need for certain skills in working with glue.

Features of work with glue

Some compounds also completely rule out the possibility of getting the mixture on the surface of the finishing materials, as this can completely ruin them. Installation of plastic skirting on the adhesive is carried out after distribution of the mixture on the back surface of the products, then the element must be leaned against the surface and pressed. Some types of glues require the need to keep the fillet on the surface for a few minutes, if for you this option is not suitable, then you should choose a composition that provides instant gluing.

Using self-tapping screws

This fastening technology is inferior in decorativeness, but it improves reliability. You will need to execute the following algorithm. Through the plinth holes are drilled, the distance between which can vary from 40 to 50 cm. In the holes it is necessary to make grooves in the form of a cone using a drill. With this approach, you can drown imperceptibly the fastener caps. At the next stage, you can install a skirting board, starting from the corner. Elements should be tightly pressed against the wall, and through the holes you can put marks using a pencil. In the marked places the master drills holes and installs dowels, then you can attach a piece of skirting to the surface of the wall and install fasteners.

Advice of a specialist

The installation of the plinth floor plastic should not be accompanied by too tight fitting fasteners, the elements should not be deformed and pushed. The algorithm described above should be repeated until it is possible to glue the perimeter of the room with fillets. Screws of screws can be masked with plugs, which are selected under the shade of the baseboard. In order to ensure their more tight fastening, they are recommended to be glued.

Use of special fasteners

If before you there was a necessity of installation of a floor plinth, as an alternative variant it is possible to use special fasteners. This technology has many advantages, but it does not exclude minuses. To advantages it is possible to carry easy dismantlement if necessary, and also simple repeated installation at which there will be no traces of fastening on a face surface of fillets. But the minus is the increased requirements for flatness of the floor and walls, this significantly narrows the scope of the use of fasteners, which is especially true for the secondary housing market. Among other things, re-installation though possible, but lends itself to implementation is not always smooth, as the fastening system weakens, and the initial density of adhesion is very difficult to achieve. If the installation of plastic skirting boards with your own hands will be carried out by you with the help of special fasteners, then at the first stage it is necessary to mark the fixing points, and after drilling the holes, the depth of which should not be more than three centimeters.

Methods of work

Next, plastic dowels are installed, screws are screwed in, as well as retaining elements. Between adjacent fastenings it is necessary to withstand distances ranging from 30 to 50 cm. It is always necessary to start work from an angle. However, in this case, it should be remembered that the installation of the first fixture from the corner should be removed by 10 cm or less.

Installing a ceiling skirting board

Installation of plastic skirting boards in the ceiling is usually carried out after the installation of plastic panels, which are attached to the frame. Once the frame system is assembled, you can proceed with the installation of the mounting profiles. If you look at the device skirting, you will notice that one of its sides has the form of a dowel, which must be stacked lining or other decorative part of the finishing material. Ceiling skirting must be installed on the top rail, which is located under the ceiling. Therefore, the frame must be installed after finishing the ceiling with PVC panels. Installation of plastic ceiling skirting can be carried out on staples or staples on wood. When the frame is made of CD-profiles for gypsum board, the plinth can be fixed to metal elements using metal screws. When there is a need to bypass the outer and inner corners, it is necessary to use connecting elements, which are selected for the color of fillets. Such an opportunity will be a good solution when the length of the plinth was not enough. When installing the connecting elements, it is best to use glue or silicone, since the insert can pop out on impact if it is accidentally hooked onto an object, this especially applies to the outer corners.

Advice from a specialist

Installation of a plastic skirting board can be put on a ledge on the edges of the finishing panels. After the installation is completed, the joints are greased with a sealant of the appropriate color. The fillets can be sewn from below to the UD profile, which encircles the room. In this case, glue is used, as well as self-tapping screws with a press-cup. At the mechanical fastening points, fillets are drilled when the possibility of cracks on the plastic is excluded, which can also be deformed. The installation of plinth plastic (its price is 130 rubles per running meter) can be installed in small rooms, while you can abandon the dredging, using screws. But in the case of corners, you can refuse to use special corners, using the same plinth, which is cut out in the stool. The resulting slots can be masked with a sealant.

Installation skirting with a cable channel

Installation of plastic skirting boards with a cable channel, in principle, is carried out according to the technologies described above. When calculating the material, one should not forget about the need to subtract the doorways and add a few percent to the length of the trimming. It is important to consider the presence of external and internal corners, connectors and plugs. Most often the plastic floor skirting board is installed in such a way that the fastening is in the wall, and not in the floor. When installing, you can use liquid nails, plugs or screws. If the wall is made of plasterboard, then it is best to use self-tapping screws with corks or glue. In the latter case, you should be careful, because if there is a gap between the wall and the skirting, it will be very difficult to remove it.

In the presence of concrete or brick in the base of the wall, the best anchoring option will be plugs. The holes for them are drilled 30 cm apart. It will be more convenient to use a perforator with a shock function to save time. The installation of the plastic skirting should start from the corner, however in the most visible part of the room one should install integral profiles. After the plinth is pressed against the surface, you should make sure that there is no gap between the floor and the fillet. Through the plastic skirting in the next stage you will need to make holes, and the formed dust should be removed by a vacuum cleaner. The next step will be the installation of plastic plugs, into which screws are screwed.