How to plow motoblock the earth? How to plow with a plow on a motoblock?

Motoblock - universal equipment with which you can plow land, plant root crops, hoe potatoes and harvest. It is worth such a dacha technique today is not particularly expensive, which determines its extraordinary popularity. Most often, they are used for plowing land for potato planting. Nothing particularly complicated technique of loosening the soil with a motor-block does not represent itself. However, it is still necessary to know certain features of this operation.

Wheel installation

So, let's see how the tiller plow lands properly. Before the operation, of course, the equipment must be prepared. On the motoblock wheel is hung, then the plow is mounted. As for the first, their diameter should be at least 50-60 cm, and width - 18-20 cm. Otherwise, quality plowing will not work. If the wheels are too narrow, the motoblock will start to wind from side to side. With a small diameter, it will not be possible to provide a sufficient distance between the soil surface and the reducer.

When choosing wheels for the motor block, you should pay attention, including on the rim. It is desirable that it is not continuous. Otherwise, there will be earth between the grooves.

Plow attachment

This operation is quite complicated - it is best done with an assistant. To hang the plow, the stunt unit is slightly raised above the ground. To do this, it is pounded onto any supports with a height of at least 15 cm. It is with this procedure that preparations for the operation of small-scale mechanization equipment intended for plowing land of any brand should begin. Including the popular, as, for example, the Neva motor-block. How to properly plow the land using the technique of this brand, will be considered a little lower.

The hinge is made according to the instruction of the motor block and plow manufacturers. When performing this operation, care must be taken that the edge of the share touches the ground with the entire surface. The plow stand should be strictly vertical, and the mound - horizontally.

Of course, the equipment should be adjusted and the width of the track. To do this, you need to pay attention to how the plow share is located. Its right edge must be in line with the inner edge of the right wheel. In this case, the plow will cut the ground smoothly and easily fall off it. The same motoblock will go easier.

Preparatory activities

On how to plow motoblock the ground, we'll talk just below. First, let's find out what other preparatory measures, besides hanging the wheels and plow, it is necessary to produce.

Before proceeding to the operation of loosening the soil, along the first row of the plot it is necessary to pull the orienting cord. Experienced plowmen may well miss this step. For beginners, however, it is necessary to perform this operation. The fact is that in the plowing process, any plow slightly moves to the right. And therefore making the series perfectly smooth is very difficult. The cord will help not to deviate from the "course".

Starting from the second, all the rows can be done and without using additional guides, since the wheel of the motoblock will go along the furrow.

How to plow?

So, the motoblock is prepared. Now you can proceed to the very procedure of loosening the soil on the site. To do less turns, plow the ground with a motor-block costs along the long side of the plot.

The handle of the motoblock should be slightly turned at the base to the left. In this case, it will be possible to go along a strip that has not yet been plowed, which, of course, is much more convenient.

Well, now let's figure out how to plow a motoblock land properly. The procedure is as follows:

• The motor block is placed on the beginning of the strip and goes along the tensioned cord.
• After the series has been passed, unfold in such a way that the right wheel of the motor-block was opposite the groove of the already plowed strip.

Doing the plowing is not slow. Do not push the motoblock. If the engine overheats (and this happens often enough), work should be stopped for about half an hour.

What to do if the soil is too hard

Next, let's see how to properly plow the plow on the motoblock land on problem areas. Normal soil has such a looseness that it can easily be pierced with a metal rod at the depth of the bayonet bayonet. On a too hard ground, the stunt unit usually starts slipping when plowing. In this case, the operation is performed twice. The first time the plot passes to a shallow depth. In the second - to the full. Some "killed" areas and do have to plow through a few tricks. But this happens, of course, very rarely.

Very hard soil should be plowed in a wet condition. Then the plow will go much easier.

What you need to know about

When plowing the first row, the plow is strictly vertical. However, starting with the second, since one of the wheels rolls along the furrow, the motoblock, and consequently the plow, slightly incline. Therefore, the plow needs to be shifted slightly vertically in the opposite direction.

To do this, in one of the adjusting grooves, loosen the nuts. After the plow has been set to the desired position, they are tightened again.

How to plow motor-block "Neva" with a plow

The garden equipment of this brand in summer residents, due to its practicality, convenience in use and low cost, is very in demand.

The power of the Neva motor-blocks is enough for the hardest soil and even for the virgin land. In the latter case, not a plow is used, but special cutters. Grass before plowing on the virgin soil should be mown. It can be removed with the use of the motor block itself (in the presence of appropriate attachments).

Actually, the answer to the question of how to plow the Neva motor-block with the plow is not difficult. Of course, in the same way as using any other similar technique. The only, experienced summer residents recommend before plowing to replace in the motor block of this brand oil. Even if it is still new.

How else can you use a motor-block

So, you now know how to plow the Neva motor-block and other similar equipment on the land. But, of course, if you want this technique can be used to perform many other operations. For example, very often motoblocks are used for hilling potatoes. In this case, other implements are used instead of the plow. This tool is called a hiller. When working, he cuts and falls off the ground in about the same way as the plow, but at a shallower depth. Okuchnikov is only two types: conventional and disk. The second option is more expensive, but in work it is much more convenient.

Sometimes summer residents use a motor-block for harvesting. In this case, it is hung with a special tool, which is a hybrid of weeding paws and gratings. When the motoblock works, it lifts the ground upwards, after which it pours back through the grate, leaving root crops on the surface.

Thus, we have found out how to plow a motoblock on the ground. This procedure, as you can see, is quite simple. In any case, it is less laborious than when using shovels for this purpose. The most important thing is to choose the right wheel and hitch the plow in accordance with all the above recommendations.