Sports and FitnessEquipment

How to make arrows for a crossbow with your own hands?

Currently, you can easily buy aluminum, fiberglass or carbon arrows for a crossbow. However, the purchase of such shells is not affordable for everyone. To save a lot on preparing small equipment, it is worth learning how to make arrows for a crossbow with your own hands.

Indicative parameters

  • The length of the arrow of the crossbow is 30-40 cm.
  • Diameter of the shaft - 5-10 mm.
  • Number of feathers - 4 pieces.
  • The height of the pen is 10 mm.
  • The length of the pen is 60-70 mm.
  • The weight of the ready arrow of the crossbow is 30-40 grams.

Quality criteria

Own-made hunting arrows for a crossbow must meet the following requirements:

  • All products have the same length.
  • Arrows differ in identical feathering and weight.
  • The stiffness of the shaft is the same for bending.
  • Arrows have approximately equal center of gravity.
  • The rods differ in slight deformation during bending.

Preparation of the shaft section

To make reliable arrows for a crossbow, saving on materials, it is enough to take as a basis pine, because such a tree is extremely common in domestic latitudes and is characterized by simplicity of processing.

Use recommended dried wood. The length of the shaft part will depend on the parameters of the existing crossbow. As for the diameter of the rod, the optimal solution in most cases is a value of about 1 cm.

After marking the workpiece, you can proceed directly to its processing. For rough heeling, it is enough to use a joinery planer. When thinning it is worth using a sharp knife with a thin blade.

How to make arrows for a crossbow in such a way that their flight proved to be extremely verified? For this, in the manufacturing process, it is necessary to ensure that the rod remains as straight as possible. After the roughing is completed, it is worthwhile to walk several times on the surface with coarse-grained sandpaper. In conclusion, it is necessary to perform a thorough grinding of the surfaces of the shaft section.

For arrows to retain their original shape, it is extremely important to protect them from moisture. For this, the surfaces can be covered with wax or other material with water-repellent properties. It is most convenient to treat with a conventional sponge or a piece of soft tissue.

Tips

Selecting the material for the manufacture of tips, preference is given to give sheet metal with a thickness of about 0.7 mm. Such a base can be easily divided into the required lengths using conventional scissors. When you modify the material, you can use a grinding stone or a file.

If there is access to the lathe, it is much more convenient to use the tips of crossbow arrows than to engage in manual metal processing. As a result, it is possible to obtain heavier and sharp products, which have an increased penetrating ability.

Once the tips are ready, it is worth starting to install them on the shaft section. To do this, it is sufficient to cut the grooves of the corresponding thickness in the end of the rods. Prepared apertures should be plentifully coated with glue, insert the tips, and then fix the connection with a dense winding of threads.

Plumage

For the production of this element, it is better to use tail goose feathers. This option looks obvious to the villager. However, where to find the material to the townspeople? If possible, you can try your luck on the market or use an alternative option in the form of blanks from plastic bottles.

The feathers can be attached to the boom shaft in several ways. Let's consider the simplest option.

To do the job, it's enough to divide the pen along the axis into two equal pieces, cutting the tapered upper and lower part along both edges. Next, it remains only to glue the feathers to the shaft with a reliable glue and, if necessary, fix it with threads.

Sighting

If there is a factory crossbow, which is fitted for the appropriate arrows, before making use of the hand-made shells, you will have to make a small reconfiguration of the sight. Performing the task should be based on the fact that lightweight poles with metal tips fly farther and faster.

Eventually

Self-made crossbow arrows - an excellent solution in terms of saving money. However, to make homemade shells could be used not only for entertainment, but also for hunting, it is necessary to try to make the polished parts as flat as possible. With the slightest curvature, the probability that the arrow will be taken to the side increases.

Particular attention should be paid to the tip. The heavier this element is, the greater the penetrating ability will be the arrow, not to mention the improvement in the smoothness of the flight.

Similar articles

 

 

 

 

Trending Now

 

 

 

 

Newest

Copyright © 2018 en.birmiss.com. Theme powered by WordPress.