Falsh-fireplace from plasterboard with own hands: step-by-step instruction, finishing

Not so long ago the fireplace performed only one function - it heated the rooms. Today, this part of the interior has become a full-fledged decoration, but not every house or apartment has the opportunity to install such a heating appliance. With the help of it you can create the feeling that you are in a posh mansion, rather than a simple city apartment.

The fireplace is able to create a unique atmosphere in the house, bringing a certain zest to the interior. Visiting stores, you can purchase a ready-made electric fireplace. However, if you carry out the design yourself, it will cost much less, and it will be quite easy to carry out the work. Such a product will not heat the room, but will create a unique design and aura of coziness.

Use for this can be ordinary drywall, with which you can create an almost complete imitation of a wood fireplace. This decision is sometimes dictated by the practical component. This is due to the fact that after the repair quite often there are pieces of metal profile and plasterboard that can be put into operation.

Preparation of tools

If you decide to make a false fireplace from gypsum cardboard with your own hands, then first you need to decide on the design of the structure, its parameters and location. Sometimes house-masters resort to making a corner fireplace, which fits perfectly into small rooms.

Having compiled the project, you can calculate the amount of material to make the design yourself. To carry out the work, you will need tools and materials:

• Drywall;
• Metal screws;
• Putty;
• Bulgarian;
• roulette;
• pencil;
• metallic profile;
• Screws for plasterboard;
• Screwdriver;
• Scissors for metal;
• building level.

Preparation before installation

Falsh-fireplace from plasterboard with their own hands to build quite simply. To do this, a sketch is prepared in the first stage, according to the dimensions of which you need to put labels on the wall, and installation will be carried out on them. When assembling a corner fireplace, the markings are taken in the appropriate corner. First, the rear part of the frame is assembled, which is attached to the wall, this will help to understand how the fireplace will look.

Assembling the frame

When you perform a false fireplace from gypsum cardboard with your own hands, you need to mount the first thing the frame. These works involve three stages. On the first, the sections of the profile are measured and marked. The next step will be their cutting and joining in a single design. The profile can be fixed with metal screws using a screwdriver.

In order for the design to look more original, a small arch is produced at the top. On one side of the profile, cuts must be made, the elements are knocked down in the form of an arc and fixed to the frame. If you decide to make a false fireplace from gypsum cardboard with your own hands, then remember that you should give the system a hardness, using jumper for this.

The maximum possible step between profiles should be a limit of 30 to 40 cm. If you plan to simulate the fireplace to the fireplace, you must first bring electrical cables to connect the backlight.

Skeleton casing

Decorative fireplace from plasterboard can be sheathed after it was possible to complete the installation of metal profiles. At the first stage the skeleton needs to be measured, marking with pencil the parameters on the drywall. The workpieces can be cut with a knife. Drywall to the frame is fixed with screws, the distance between which will be a limit of 8 to 10 cm. Drywall can be any, for example, water resistant or conventional. It is better to use one that is intended for installation on a wall. Sometimes used and ceiling, but it has a smaller thickness.

Methods of work

When the decorative fireplace is made of plasterboard, the frame is recommended to be made separately, and then proceed to fix it to the surface. If the design on one side will be located pretty close to the wall or abut it, then you need to attach the drywall and only after fixing the construction to the main wall.

If you neglect this recommendation, then there will not be enough room to fit the screwdriver. Gypsum cardboard in this case can be strengthened with a screwdriver, which is quite difficult. In order to rationally use sheets of drywall, the frame is equipped with jumpers corresponding to the size of the pieces of finishing material.

Bending of the workpiece

Decorative fireplaces for an apartment can assume the presence of a bend. To begin with, you should execute its template. Then a strip of the necessary sizes is cut from a cloth which can be laid from the inside of the future bend. A lot of 5 mm holes are made on this part. Punctures can be made with a needle roller. Holes are needed to damage the cardboard layer.

The workpiece is wetted with water, and after the core is softened, it can be fixed to the template and left until it dries. Water should not penetrate a solid layer of cardboard, otherwise the product may break. To bend a profile from metal is simple enough, for this purpose on the lateral sides it is necessary to make cuts, the distance between which is 1 cm.

Fireplace Finishing

If you are thinking about the question of how to trim a false fireplace from gypsum board, then you can use the method of puttying seams and joints. At the same time you need to stock up with a putty tape. If the surface is not stained or covered with a film, this is not necessary. The ends of the sheets must be well aligned, like the intersecting planes.

The cladding should not be continuous, because the devices installed inside will need heat removal. If you plan to put a heater inside, it is important to ensure that there are ventilation holes that should be located at the top of the structure. A false fireplace from plasterboard in the interior will look great if you decorate it. For this purpose, ready-made panels or tiles are often used. You can apply the dyeing method to lime or to surface the metal.

As practice shows, one layer of putty will not be enough to achieve smoothness of the surface, so the substrate must be primed, dried and again covered with putty. If you are satisfied with the result, you can start grinding the surface. For this, fine-grained sandpaper is used. At the final stage, an artificial stone or a facing brick can be used. Effectively in the interior will look plaster moldings, the elements of which can be glued to the surface. After this, the structure is painted in a suitable shade.

Tips of the master on furnish

For decoration, you can use a mirror, wallpaper or paintwork materials. You need to trim the furnace, and you can use ceramic tiles for this. It can be glazed, and its shade, shape and texture can be very different. Cut the tile to fit it in size, you can use a grinder or a tile cutter. In this case, the falsh-fireplace with its own hands, the step-by-step instruction for the manufacture of which is described in the article, can be decorated only with tiles laid on a previously primed base.

Further, an elastic adhesive based on cement is mixed. The mixture is applied with a spatula on the tile, the alignment can be done with a toothed shovel. The thickness of the layer should be 5 mm or less. Begin work from any of the lower corners. Between the rows you need to insert the crosses to achieve the same thickness of the seams.

Correct laying of the material should be checked using the building level, while excluding the mixture on the front surface of the finish. When a false fireplace is made by yourself, a step-by-step instruction on how to make it should help you avoid mistakes, after drying the composition, which will take several days, you can begin to grout the seams. The protruding sections of the glue are cut with a knife, the seams are cleaned with a soft sponge.

Grout should be applied from a confectionery syringe or with a thin brush. You can get rid of surplus dense sponge. The same technology is suitable for finishing the drovnitsy. Instead of tile glue, liquid nails can be used, this will speed up the process.

Finishing the portal

The fireplace, the drawing of which is presented in the article, can have a fire chamber and a portal made of smooth-painted surface or artificial gypsum stones. The portal frame is made of wood, but ceramic tiles are also suitable for this. Pre-primed base of gypsum board is painted with water-based solutions. The first layer is applied with a brush, all subsequent - with a roller. Between the layers, wait until the surface dries completely. Excellent will look under any light matte paint light tones.

Making a corner fireplace

The dimensions of the false-fireplace from the plasterboard, if it will be installed in the corner, will be determined by your preferences. For the framework, you need a metal profile, in addition, you need to prepare the rack profiles with dimensions of 60x27 mm. The guide profiles must have dimensions equal to 28x27 mm.

Screws will have a length in the range from 14 to 16 mm. To join the plasterboard and the frame you will need self-tapping screws with a countersunk head. Many craftsmen recommend to use for disc cutting of drywall a disk hand saw, the cutting depth of which varies from 16 to 24 mm. However, if there is no such tool in the arsenal, you can do with a kitchen knife.

If you decide to perform such a fireplace, it is recommended to prepare the drawing in advance. On it, you can specify the height of the structure, which is 898 mm. As for the width, it will be equal to 1041 mm. Each side will be 737 mm. As for the fire, in this case you can use the electronic photo frame. Its application will be safe.

With the help of a screwdriver and self-tapping screws, the UD profile needs to be reinforced to the floor surface. The distance between the fasteners should be 30 cm. The strip will be located in parallel with the wall, it should be installed first. The side elements must be fixed in such a way that they do not go beyond the first profile. On the base wall by marking, you need to strengthen the wall profiles. The finished fasteners are set UD-profiles, then those that will be located parallel to the surface of the floor.

Conclusion

An angular faux-fireplace made of plasterboard can be finished using independently made gypsum stones. To do this, prepare a silicone mold, the inner surface of which is lubricated with petroleum jelly. It is poured divorced to the consistency of sour cream gypsum, and the surface can be leveled with a spatula.

The material will be ready in 20 minutes. Decorative fireplaces, intended for an apartment, are often decorated with gypsum stones, which are made using pigments. If these were not at hand, the surface of the stone can be varnished after hardening.