The doors of the closet with their own hands. How to assemble and install sliding doors for the closet with your own hands? Mounting the doors of the closet with your own hands

In order to save some people start to make furniture themselves. For example, if you purchase material and accessories, you can get an inexpensive cabinet with sliding doors. Today such products are in great demand, since they save a living space, are convenient to use, decorate the interior (concerns models with an original and interesting view). The following describes how to prepare and mount the doors of the closet with your own hands, and also decorate them unusually.

Varieties

Before embarking on production work, it is necessary to understand what kind of constructions are there at all. Coupe doors are completed with a suspension system, an overhead or frame profile. Suspended products are considered the cheapest, because they consist of a blade of particleboard and a cladding edge. On its inner side at the top are rollers, and below - the guiding elements. Such a system is difficult to regulate, quickly fails, and the cloth is prone to bending.

The overhead profiles hold the chipboard better, since they are located on the sides. If you need these doors of the closet with your own hands, then the lower rollers equipped with bearings will act as a support. In the upper part, there are also rollers, but they perform the support function. If there is an obstacle in the way of the doors, they can skew and jump out of the grooves.

Frame profile is a design of horizontal and vertical elements. They are made of steel (aluminum) and make the product more durable and reliable. Rollers on the doors move not only to the sides, but also vertically. A glass or a mirror can easily be inserted into the canvas.

Sizing

To make furniture look neat, you need to correctly measure the door of the closet. With their own hands make them a width of 500-1000 mm. Too small a door will collapse, but too much is difficult to operate. The height of the structure depends on the type of profiles. For example, the overlaid elements have a length of 5500 mm, so they can be adjusted in height.

When calculating the width of the doors, it is necessary to take into account the overlap. Therefore, the width of the profile is added to the measurement of the opening, and the total amount is divided into two (the number of canvases). If there are more doors, then the number of profiles will increase.

The height of the door-compartments is calculated much easier: you need to measure the opening for height and subtract 45 mm from it. This distance allows you to put the canvas in the upper profile. Do not subtract less than 45 mm, otherwise the doors will get stiff.

Material

How to make the doors of the closet with your own hands and what material for this use? His choice depends on the financial abilities and design preferences of the consumer. Most often in the calculation take chipboard, glass, mirrors, plastic, etc. Doors made from chipboard mimic the natural material, make the interior homely, warm and interesting. They are used in the manufacture of budget cabinets, because they have a low cost.

Glass structures can be: matte, patterned, colored or embossed. They are pasted with a special film, which, when impacted, will not allow the material to break into small pieces. Mirror doors also look very exquisite. They can be tinted, covered with anti-glare film, equipped with built-in lamps, patterns and patterns.

Quite often there are doors made of acrylic plastic - a very durable material. Its color palette is diverse, which allows you to create an individual design. You can get a unique interior if you combine this design with the decoration and other interior details.

Fasteners and guides

You can install the doors of the closet with your own hands if you purchase the necessary fasteners (rollers, screws, adjusting screws, guides, etc.). The bulk of their weight falls on the bottom, so there should be large rollers. Top rollers are small in size, because they are only needed to support the structure and move along the guide profile. Adjustment screws with fine threads, which are responsible for the slope of the doors, will also be needed. The main fasteners are self-tapping screws that connect the elements into a single product.

For moving the doors inside the cabinet, horizontal guides meet. The top profile is a horizontal part at the top of the door frame, which has a filling in the form of a particle board or a mirror. A special groove for screwing the screws is passing along it. With the help of the lower guide element the vertical profile is fixed, the carrier rolls are concealed, the appearance improves.

It will not be possible to make sliding doors for a compartment-compartment with own hands without a vertical profile-handle. On it there is a groove into which the filling is inserted. This element makes the product attractive, because it looks very elegant.

Door assembly

After taking the measurements, the choice of materials and fittings begin the assembly of the doors. First prepare the filler. Exactly around the perimeter of the silicone sealant. Then it is applied to the main material and attached to it from above and from below by horizontal slats. It is very important that the mirror goes into all the grooves, and the sealant is not visible.

When making the door of the cabinet-compartment with their own hands, the side racks are also arranged. For this, the design is placed on the edge and put on a mirror. Elements of profiles are fastened together by self-tapping screws, for which pre-prepared holes are needed. After this, rollers are installed at the top and bottom, and a tape with a pile is glued to the vertical profiles. If necessary, the design is equipped with handles (screwed with screws or inserted into the cut hole).

Preparatory work

Before you perform the installation of the doors of the closet with your own hands, prepare the opening. To begin with, the horizontal and evenness of the guides is checked. The entire structure must have a strict geometry, but small errors are hidden in the process of adjusting the doors. You can also align the cabinet using the tuning legs (especially if the floor has irregularities).

If you intend to mount a built-in closet, you will have to prepare an opening. To begin with, measure its width again and cut out of the chipboard two pads. Their size should coincide with the width of the opening (maximum accuracy is required). With the help of a drill, several holes are made in them. Lining is applied to the ceiling, leveled and attracted by screws so that they are imprinted. In the designated places holes are drilled and dowels are blocked. The details cut from the chipboard are screwed with screws. The lower lining is mounted in the same way as the upper lining. It is very important that it is perfectly even.

Installation work

The installation of doors in the closet with your own hands begins with the laying of the guides. First take the top element, measure the desired length and jigsaw cut off excess. The same is done with the lower guide element. Using a drill, drill the holes necessary for fixing to the cabinet parts or linings. The guides are applied, leveled and fixed with screws.

Once everything is finished, you can proceed with the installation of the doors. The first sheet is inserted into the guides, the system is operational and the adjustment is performed. Correctly adjusted doors will allow the mechanisms to work quickly and easily. After that, install the second cloth, check and adjust it. Sometimes install three-leaf sliding doors for the closet with their own hands. Then the assembled flaps push back and mount the third sheet. With him, all the same manipulations are carried out as with the previous elements.

Decoration

At any time, you can remove the doors and decorate them with different materials. In this case, you can choose: mirrors, patterned glass, leather and fur, various films.

1. The mirror is very often inserted into the doors of the wardrobes, especially if the furniture is located in the hallway. For interior decoration, silver and bronze products are best.

2. Patterned or ordinary glass, covered with decorative film, looks great on furniture designs. Individuality will be given to the room by custom-made material.

3. Photo printing looks very nice and allows you to create absolutely any images. At the same time, the picture is applied either directly to the surface or to a film that is glued under the glass.

4. Decorating the door with the help of leather and fur. Today, decorative panels, imitating the skin and fur of animals, are in great demand. If desired, they are applied various drawings and patterns.

5. Special films allow you to quickly and cheaply decorate the product. A variety of colors and textures will help to combine furniture with any style of interior.

The closet is popular with consumers due to its spaciousness, space saving and attractive appearance. It will cost less if you figure out how to assemble the doors of the closet with your own hands. And if the apartment has a roomy niche, then it can be protected and get an excellent dressing room.