Rubber floor. Rolled rubber coating for garage

When decorating floors, it sometimes becomes necessary to create a strong and reliable coating that will be perfectly matched by mechanical impact and frictional force. The surface must be able to withstand moisture, have a minimum expansion coefficient and transfer the influence of chemicals. It is for this purpose that the rubber floor is used.

The main varieties

A fairly modern and convenient option for floor design is a rubberized coating. However, to begin with, it is important to determine which variety of this material to choose. Among others, it is necessary to distinguish a roll material, which has a thin layer at its base, capable of protecting against cold and noise. This coating has incisions that increase friction. This indicates that the surface is able to withstand slipping even at high humidity.

The second version is separate modules, which are made of thick rubber. They have the form of tiles and are represented by original puzzles. In addition to the usual characteristics discussed above, such modules have specific qualities, for example, they are capable of undergoing high loads and a strong mechanical effect. Such a coating can withstand acids and active media.

Features of preparation

Before laying a rubber floor covering, you must prepare the surface. From the professionalism and thoroughness of this stage depends the evenness and quality of the resulting gender. As the main requirement to the bottom is the absence of large differences in height. Cracks and potholes on the surface should not be. The following types of grounds can serve as a basis:

• Ground;
• Asphalt;
• Concrete;
• Cement;
• Wooden.

Preparation involves leveling in height, applying putty, dedusting and priming. In the case of laying a rubber roll coating on an open site, it is necessary to ensure a natural gradient. It is possible to supplement the coating with a drainage system, which provides for troughs and inclines. In this case, even after the rain, the rubber surface will remain dry.

Special Features of Rolling Coating Installation

If you decide to lay the rubber floor, then first you need to prepare the surface. For this, a leveling mixture is usually used, which will achieve an excellent result. On the surface in the next stage a thin layer of glue is applied, only after you can proceed to rolling the material.

If you decide to use modules, then it is better to apply the compound on their back surface. For roll rubber a tight roller is used, with which you can remove excess air from under the cover. Such surfaces are tried to perform without seams, but if necessary they can be sealed with a special compound of raw rubber and fixed with a heater. Usually, a vulcanizer or soldering iron is used for this.

Features of work

Spread the rubber floor better by enlisting the help of another person. This recommendation is due to the fact that one roll of material usually weighs about 120 kg. Joints can also be glued with double-sided adhesive tape, which will increase the strength of the coating.

After the roll is rolled up, it is necessary to cut it at the edges, guided by the size of the room. To do this, use a chalk, a measuring device, a rule and a paint knife. It is worth noting that the rubber floor is laid with double-sided tape, if you do not plan to mount the coating on the adhesive backing. This approach has its advantages, which are expressed in the fact that the material, if necessary, can be reused in other areas. In addition, this technique is used in the temporary laying of sex.

The surface must be firm, even and dry. If concrete is used as the base, then it is necessary to sustain it after pouring for 28 days. The material can also be laid on a wooden base, which must be dry. Its humidity should not be above 10%.

It is important to make sure that the substrate is uniform, cleaned from the old paint and has a smooth topography. To lay a rubber covering for a floor in a case with a wooden basis it is possible only on a strong surface. As soon as you measure the rubber and mark the places of its cutting it was possible to roll the roll back.

Technique of arrangement of rubber floor

When dealing with a wooden covering, you must sand it and coat it with a primer. Do not put moisture on the surfaces to be bonded. The quality of work depends on the choice of glue. The surface can be used after 24 hours. With this technology, you can arrange roll coatings with any thickness.

Cost of coverage

If you do not plan to work on your own, then you might be interested in the price of a rubber floor. Work on laying will cost 400 rubles. Per square meter. In this case we are talking about stables, stadiums, sports halls, etc. But if it is necessary to carry out the work on laying the treadmills from the described variety of cover, then such work will cost 1250 rubles. Per square meter.

Additional expert advice

If you have chosen rubber floors for a garage and plan to tackle their laying yourself, then after preparing the surface, roll the roll along the wall and leave it to rest for 12 hours. Cutting material should be carried out with allowance. It should be found on the wall by 15 cm. This is necessary to reduce the shortcomings of the room due to the curvature of the walls.

By this method, all rolls are cut. Cloths should be adjacent to each other end-to-end. Before laying a roll rubber coating, you should take care of the presence of some tools, among them a construction knife and a metal ruler. As soon as the canvas is laid on the floor after applying the adhesive composition, you can cut off the left overshoes. This step must be carried out in several approaches.

Conclusion

Using two-component adhesive for laying the rubber coating, you should take care of the availability of a special container for its preparation. To draw the glue you will need a rectangular spatula. But put the mixture on the surface will have a notched trowel.