LEDs for DRL. DXO own hands of LEDs

LEDs for daytime running lights (DRL) are produced in various capacities. The brightness parameter varies from 20 to 50 microns. It is also important to note that the LEDs differ in terms of the luminous flux.

Many daytime running lights are made with contact adapters. Their conductivity parameter is very high. LEDs instead of DRL are installed frequently. However, it is important to note that the models on the market are expensive. If necessary, daytime running lights can be made by yourself.

Daytime running lights with your own hands

Doing DRL with your hands from LEDs is pretty simple. In this case, the adapter is selected as the contact type. To improve the conductivity of the current, an expander is used. Most often, it is selected open or impulse type. Some models use a fuse for protection. To build the model, LEDs are first installed. A powerful converter is also required. A 3A model will do fine.

Then, to make DRL with your own hands of LEDs, you need to take a tetrode. Parameter of maximum resistance for it must be no more than 50 Ohm. In some cases, the controller is used without an isolator. A two-wire cable is used to connect the daytime running light.

LED for model "Eagle Eye"

LEDs for DKO "Eagle Eye" have a lot of advantages. First of all, it is important to note that they have excellent brightness. Many experts say that they have low heat losses. The power of this model is 20 watts. For pulse expanders, the device fits perfectly. The filter in this case is absent. To protect against phase noise, an adapter is used.

The output voltage in the device reaches a maximum of 12 V. The parameter of the threshold resistance here is 45 Ohm. To reduce the sensitivity, a capacitor is used. In the installation, the LEDs for DKO "Eagle Eye" are very simple. The service life of this model is about 8 thousand hours. The system for protection against impulse noise is used in the third class. The minimum permissible temperature for operation of daytime running light LEDs is -15 degrees.

Light-emitting diodes for the device "Mayak"

LEDs for DDO "Mayak" are very popular. In this case, the power is 15 watts. As experts say, the adapter is used with a quality filter. If we talk about indicators, it is important to note the high level of conductivity. The output voltage of the model is 12 V.

The trigger in the device is of the open type. Voltage dips do not occur often. The system for protection from impulse jumps is used in the second class. The luminous efficiency of the presented LEDs of daytime running light is 320 lm. The current consumption in this case does not exceed 3.4 A. The high frequency deviation LEDs for DXO "Mayak" are not afraid. The transceiver is of a commutated type.

LEDs for the Philips model

LEDs for DKO "Philips" have a high conductivity. Their brightness is 30 microns. As experts say, they have very rare problems with overheating. In this case, the output voltage is at the level of 10 V. The sensitivity index on average reaches 5 mV. Luminous feedback from models is low. The current consumption indicator does not exceed 3.3 A.

The minimum permissible temperature for LED operation is -10 degrees. The transceiver in the device is of the operational type. In total, the model has one filter. Trigger in LEDs for DKO "Philips" installed two-pin type. The maximum resistance is at 45 ohms.

LEDs for devices "Grant"

Light-emitting diodes in "Granta" have a high brightness. The conductivity parameter is 4 μ. Experts are sure that the system from phase jamming is used of high quality. The sensitivity in the device is 5 mV. Problems with overheating of light-emitting diodes are observed extremely seldom.

Light output of the model 350 lm. The minimum permissible temperature for storage and operation of the LEDs is -25 degrees. The device is installed through the contact adapter. The output voltage of the LEDs is 10 V. The filter is used by the network type.

Parameters of LEDs Falcon DRL032

These LEDs for DRL are excellent for cars such as Ford and Hyundai. The heat losses are low. However, it is important to note that the model has obvious shortcomings. First of all, these are problems with overheating. The filter of the model is of the network type. The current consumption is 3.4 A. The output voltage of the LEDs reaches a maximum of 12 V. The transceiver has a wave type for the daytime running light. The adapter is used with a trigger. The sensitivity index reaches a maximum of 6 mV. The system for protection from impulse oscillations is used in the third class.

LEDs Falcon DRL040

These LEDs are suitable for models that have a pulsed transceiver. In this case, the brightness parameter is 5 microns. Experts say that the impulse noise to the device is not terrible. The system of protection against power surges is. The current consumption of LEDs at the level of 4.6 A.

The output voltage of the model is 12 V. The conductivity of the current is at a high level. For models "Ford" and "Honda" the device fits perfectly. It is also important to note that these LEDs can boast of low sensitivity. Their service life is 13 thousand hours. The thermal losses in this model are low. For daytime running light with flip-flops the model is suitable. The frequency deviation is not more than 5 Hz.

Description of LEDs Falcon DRL045

These LEDs for DRL are often installed on the machines "Mazda" and "Toyota". Their conductivity parameter is 5 microns. The overload protection system is installed in the third class. As experts warn, the device is not afraid of high temperature. In this case, the trigger is of the condenser type. The decrease in sensitivity is gradual. Current consumption at 5.7 A. The output voltage of the LEDs does not exceed 12 V. The system for phase-noise protection is not available. The maximum resistance is 46 ohms.

Parameters of LEDs Osram 100

These LEDs for DRL are often found on the cars "Ford" and "Mustang". Among the features of the models should be noted a high sensitivity parameter, as well as brightness. Speaking about the indicators, the output voltage reaches 15 V. The negative resistance of the LEDs does not exceed 45 ohms. The current overload indicator is at 5.3A.

The thermal losses in the model are low. Short-circuits LEDs are not afraid. In this case, the decrease in sensitivity occurs gradually. For daytime running light on the triggers the model fits perfectly. Problems with overheating are very rare. The device is not afraid of high temperature.

LEDs Osram 110

For DRL, the super bright LEDs Osram 110 are excellent, they have a high conductivity, so they are in demand. The decrease in sensitivity occurs gradually. For brands Ford and Honda, the device fits perfectly. It is also important to note that the device is used in models on triggers.

The parameter of the output voltage is 10 V. The filter of the LEDs is of the network type. The transceiver in this case is installed with an open conductor. The current overload reaches 5.8 A. Experts say that the transceiver rarely overheats. The system from impulse noise is used in the third class.

Description of LEDs Osram 125

These LEDs for DRL are often installed on Honda and Hundai cars. In this case, the adapter is used with a trigger. According to experts, the brightness parameter of the model is low. The maximum resistance is 46 ohms. The frequency deviation in the device is negligible. The output voltage of the LEDs is 12 V. The system for protection against impulse noise is used in the third class. The thermal losses of light-emitting diodes are insignificant. It is also important to note that the model is suitable for daytime running light with pulse transceivers.

Sirius NS-4207 LED Parameters

For DRL, the super bright Sirius NS-4207 LEDs are good, they have good sensitivity. They perceive the eyes very gently. The trigger in this case is of the wave type. As experts say, the conduction parameter is very high. The phase-jamming protection system is of high quality. The output voltage of the LEDs is 12 V. The model is not afraid of high temperature.

The permissible humidity level for LEDs is 60%. The maximum light output is 450 lm. According to experts, the device copes well with a decrease in sensitivity. Current overload in LEDs reaches 3.6 A.

LEDs Sirius NS-42055

The LEDs of this series are equipped with high-quality filters. Also worthy of attention is the trigger. Many experts note that problems with heating the adapter are rare. The light output parameter is a maximum of 460 lm. The system for protection against impulse noise is used in the third class. The above model is not afraid of increased temperature. The permissible humidity level for LEDs is 50%. For cars of "Honda", "Mazda" and "Toyota" models, the device fits perfectly.

The system of protection against power surges is. The filter for LEDs is a network type. If we talk about the indicators, then the resistance reaches a maximum of 45 ohms. The frequency deviation in the device is 4.5 Hz. The output voltage of the LEDs does not exceed 20 V. For daytime running light systems with wired triggers, the device is not suitable.