Installation of a toilet bowl on a tile. Installation of a floor toilet: instructions

Most experts believe that the installation of a toilet in a private home should begin with the entire complex of finishing works in the toilet or bathroom. After that you can start installing plumbing. Further in the article we will consider in detail how to install a toilet bowl on a tile. You can completely do it yourself.

General information

Depending on the model of the product, the technology is determined, which will be used to install the toilet bowl on the tile. Currently, these sanitary fixtures are being manufactured with both external and internal type of connection. For this reason, the installation of the toilet bowl (the price usually offered by specialists will be given below) depends on the particular case. But first things first.

Approximate cost of work

The installation of a toilet bowl, the price of which depends on the type of model, can be carried out by the employees of the store in which the product is purchased. Usually installation does not take much time.

• Installation of a floor toilet - 1500 rubles.
• Installation of the imported model (the cost of which exceeds 15 thousand rubles.) - 1,700 rubles.
• Installation of a lavatory toilet bowl - 1500 rubles.
• Installation of the suspension model is 1700 rubles.

Required Tools

Before installing the toilet on the tile, you should prepare everything you need. For installation, you will need:

1. A pipe or corrugated pipe.
2. Silicone sealant.
3. Sealing tape FUM (for threading).
4. Drills for concrete and glass.
5. A ball valve for a pipe that will supply water.
6. Flexible hose.

The following tools are required for the job:

1. Pencil.
2. A hammer.
3. Drill or perforator.
4. Kern.
5. Adjustable wrench.
6. Rubber spatula.

Compatibility of sinks

In this case, the main factor is the type of wastewater produced in the house. This determines the choice of toilet bowl, as well as the way it is connected to the sewer drain. There are several types of water discharge.

1. Vertical. This type of descent is considered obsolete. In accordance with the design, the sewer pipe goes to the floor vertically. This type is found in old houses, especially in stalinkas. In modern construction it is not popular. However, this method helps to save a lot of space in the toilet if necessary. Thanks to him, the installation of the toilet bowl "compact", for example, can be carried out directly on the pipe.

2. Horizontal. Currently, it is the most popular way of laying sewage. The connection itself is made to the connection fastener. It is located horizontally.

3. The oblique issue. It is suitable for all types of sewerage.

Some installation features

Suspended toilet bowls are not so popular today, as, for example, traditional floor. The fact is that the former are quite expensive compared to the latter. When installing a suspended structure, it is necessary that the distance from the floor surface to the seat be observed. The optimum height of the toilet is about 40 centimeters. In this case, the product will be convenient to use. Installation of a toilet bowl on a tile is carried out by means of eccentric cuffs, fan, corrugated or plastic pipes. Next, consider these elements in more detail.

FAN PIPES

This method of connection is considered the most beneficial from the point of view of aesthetics. Pipes and toilet are visually transformed into a single design, which fits perfectly into the interior of the bathroom.

Eccentric cuffs

With their help the toilet can be connected even to the most inaccessible places. The same can be said about corrugated pipes. A feature of eccentric jumpers is that they rotate around their own axis. Thus, the inaccuracies of the connection are smoothed out.

Plastic pipes

They are easy to install and practical. For this reason, many specialists stop the choice on them. Currently, there are a huge number of types of plastics. This industry continues to develop actively. So you can safely choose plastic pipes as the most technologically advanced.

Features of external fastening

Installation of a toilet bowl on a tile is carried out by means of bolts. It is necessary to put the product in place for installation. The tiles are marked with a pencil. Further it is required to remove the toilet bowl to the side. Drill holes in pre-marked areas. There will be dowels. First of all, you need to use a drill bit for tile and then only for concrete. It is required to clean the holes of dust. After that, they must be filled with silicone. The latter is used as a waterproofing. Then dowels must be inserted into the holes. After this, the toilet is installed on the tile to the designated place. However, a silicone sealant must first be applied along the contour . Thanks to it, moisture does not fall under the base of the product. The bushings must be inserted into the mounting holes. They are screwed with screws. Also it is necessary to fix the plugs. Most often from the bottom of the toilet bowl are excess silicone. They should be removed with a rubber spatula.

Nuances of internal fastening

Before installing the toilet bowl on the tile, you need to pay attention in advance to the outlets to the water supply and sewerage systems. Also it must correspond to the pre-arranged apartment repair plan. Outlet holes are supplied for a specific toilet model. This plumbing fixture can be connected in several ways.

Progress

As it was said above, fastening is carried out by means of bolts. In the process of working with ceramic tiles, the drill can slip. To prevent this from happening, you need small chips at the drilling sites with the help of a core. In a floor tile it is required to make four holes. The depth, which is equal to the length of the dowels, must be reached. Then you need a hammer. With it, the dowels are hammered into the drilled holes. The hammer should be operated carefully so as not to damage the lining. Do not tighten the bolts immediately. Perhaps in the future a fit will be required.

Features of mounting corrugations

It has a large number of internal membranes. Gofra is fastened in the production hole on one side, and on the other - on the outlet pipe of the toilet bowl. Thanks to it, the distance to the wall is easily adjustable. In addition, the installation of the required angle of connection passes without complications.

Pipe connection features

An external water supply system is present in many toilet models. However, there are products that are equipped with a hidden configuration. Each joint must be leakproof and not leak. The clamping nut is put on the copper tube in the reverse order. The thread of the pipe coming out of the wall requires attention. It can be both external and internal. In the latter case, an adapter is required. For sealing, it is recommended to use the FUM tape.

Important information

First, the corrugated pipe is installed in the sewer hole. It is in the floor or in the wall. In this case, the adhesive is not recommended. Through the adapter, the copper tube is attached to cold water. Fastening of a toilet bowl is carried out after the device of all connections. First tighten the outer bolts. Then the installation of the toilet is finally verified. After that, the bolts on the fasteners are tightened.

Installing the drain tank and lid

They are the last ones to install them. The tank and cover are usually present in the kit. However, some manufacturers provide the choice of the last detail directly to users. In this case, the cover will need to be purchased separately. Tighten the mounting bolts from the underside. To do this, you need a metal nut of large diameter. Then you can proceed to install the cover of the tank. Also, you need to secure the reset button. Do not allow metal parts to come in contact with the ceramic. For this, plastic or rubber gaskets are used. Then you need to check how the toilet works. During the inspection of all connections, possible leakage is identified.

Final moments

The easiest way to install the toilet is bolted. Accurate mounting with screws reduces the risk of defects due to water. To install the toilet, you can invite a specialist. However, you can save money by doing the installation yourself. In general, the work is not accompanied by difficulties.