Horizontal pump: types and specifications

Horizontal pumps are often installed in sewer systems. Also devices of this type are suitable for pumping water or oil. The main parameters include power, as well as pressure. The flow rate is measured in cubic meters per hour. In order to understand the features of pumps in more detail, it is necessary to consider the existing types.

Classification

First of all, the pumps are distinguished by the number of wheels inside the chamber. There are single-stage, two-stage and multistage devices. It is also important to note that the shaft can be located in a horizontal or vertical position. In a separate subcategory, console devices are selected, in which the drive is located at the top of the structure. Liquid suction can occur through one or two holes. Depending on the type of tap, devices with spiral and shovel channels are selected.

Dab A 50 pump

This single-stage pump (circulating horizontal) is produced with a power of 8 kW. He has only one outlet pipe. The pressure chamber in the device is missing. The impeller is in the horizontal position. The diffuser is made of fine-grained cast iron. The maximum head is 22 meters. The diameter of the impeller is 350 mm. The feed parameter averages 310 cubic meters. Meters per hour.

Description of the model Dab A 60

These horizontal cantilever pumps are produced with a power of 3 kW. The pressure chamber in the model is provided in a longitudinal shape. There is one branch for the outlet of the liquid. The impeller is located in a horizontal position. The diffuser in the horizontal pump is installed from fine-grained cast iron. The shaft in this case is fixed behind the protective sleeve.

If we talk about the parameters, the mass is 450 kg with the drive. The flow rate is 230 cu. Meters per hour. The feed rate is 30 meters. The impeller is installed with a diameter of 420 mm. The bearings in the device are located under the flange gasket. It is also important to note that the model has a sealed padding. To increase the pressure there is a sealing ring.

Characteristics of pumps Dab A 75

This two-stage pump (horizontal monoblock) is manufactured with a large diameter shaft. The protective plate for it is made of steel. The pressure chamber is provided without a diffuser. The outlet pipe is located at the rear of the structure. In total, the model has two impellers. Their diameter is 430 mm. The shaft is fitted with a compensation ring. The hub in this case is attached to the base of the chamber. A steel cover is provided to protect the bearings. The upper bushings in the horizontal pump are inserted from the bronze.

Sprut JDW 11

These pumps (fecal horizontal) are produced with a powerful drive. The limiting mass of the model is 355 kg. In total, the device has two outlet nozzles. The pressure chamber is located in the front of the housing. The impeller is used with a diameter of 460 mm. The body of the model is made of fine-grained cast iron.

In total, there are three bushings in the device. The O-ring on the shaft is made of rubber. A special protective plate is provided under the diffuser. The retaining ring in the device is made of steel. The feed parameter is no more than 230 cu. Meters per hour. The electric motor is 12 kW. The head is equal to 45 meters.

Sprut JDW 42

This pump (horizontal monoblock) is manufactured with a steel diffuser. In this case, the manufacturer provides one pressure chamber. The shaft diameter is 34 mm. The inlet pipe is located at the rear of the housing. The impellers are in a horizontal position. The body is made entirely of fine-grained cast iron.

It is also important to note that one end of the shaft is fixed on the steel bushing. The side bearings of the model are made of bronze. To increase the allowable pressure, a protective cover is used. It is installed in a horizontal pump under the diffuser. In total, the model has three pads. The upper flange is fixed by the bracket. The sebaceous stuffing is applied with a small thickness.

Sprut JDW 55

These pumps (fecal horizontal) are manufactured with two pressure chambers. It is also important to note that the device withstands high pressure. The outlet connection is connected to the diffuser. In this case, the shaft is set to a small diameter. To increase the pressure, a circlip is used. It is made entirely of steel and is capable of withstanding heavy loads.

If we consider the parameters, it is worth noting that the diameter of the impeller is 402 mm. The feed rate is a maximum of 340 cu. Meters per hour. Head - not more than 50 meters. The drive is installed in this case with low power. The maximum weight of the pump with a stand is 322 kg.

Characteristics of Saer NCB32 pumps

This horizontal pump is manufactured with two impellers. The diameter of the outlet branch pipe is 34 mm. The pressure chamber is provided in an elongated shape. Due to this, the model has a very high head pressure. The indicator of the limiting pressure is at the level of 3.4 Pa.

The diffuser in the device is located above the shaft. Fastening of the compensation ring is carried out through the protective plate. The side bearings in the device are made of bronze. Also of the features it is important to mention a large gasket over the diffuser. Thus, the model is capable of pumping liquid of various densities.

Parameters Saer NCB40

These horizontal water pumps are multi-stage. The drive in this case is used at 4.6 kW. All this allows you to withstand a lot of pressure. The pump body is made of fine-grained cast iron. However, all bushings are made of stainless steel. The shaft of the model is installed with a diameter of 57 mm. The bracket is used with a protective plate. The maximum weight of the pump is 285 kg. The feed rate reaches a maximum of 310 cubic meters. Meters per hour. The index of pressure is not more than 46 meters.

The pump "Grundfos 5RT"

Horizontal pumps "Grundfos 5RT" differ in the volume pressure chamber. In total, the device has two outlet nozzles. Their diameter is 46 mm. The impeller is fixed behind the shaft. The diffuser is completely made of fine-grained cast iron. The bushings of the model are made of chrome-plated steel. O-rings are usually made of rubber. It is also important to note that the model provides one padding under the shaft.

Description of the model "Grundfos 3RT"

Horizontal pumps "Grundfos 3RT" differ from other models by a large suction channel. The outlet is located at the rear of the housing. The diffuser is made of a small diameter. In total, the device has two impellers. The drive is connected to the pump by 4.3 kW. There is a sealing ring under the flange.

Bearings are only ball type. Side sleeves are made of chrome-plated steel, they can last many years. The disadvantages of the model include a small bracket on which the front edge of the diffuser is fixed. It is made entirely of fine-grained cast iron.

Parameters Saer NCB69

These horizontal water pumps are notable for a large camera. In total, the device has two outlet nozzles. The drive is installed in the rear of the structure above the diffuser. The power of this model is 4.7 kW. Compensating rings are applied along the sides of the shaft. They are made entirely of stainless steel. In this case, the suction nozzle is provided with a long channel. Its diameter is 45 mm.

The stuffing box is located behind the diffuser. In order for it not to wear off, a protective sleeve is used. The bracket of the model is made of fine-grained cast iron. The pump head is 35 meters. Weigh the indicated device with a stand of 329 kg. The feed rate reaches a maximum of 340 cu. Meters per hour.