Dimensions of the sibit: table, GOST, types and reviews

Recently, for the construction of houses and buildings for various purposes, sybit is increasingly being used, which is a material in the form of aerated concrete blocks, performed by autoclave technology. It looks attractive, has low weight, high strength and is excellent for low-rise construction. These characteristics are used not only by professionals, but also by private developers around the world. Even for the frosty regions, Sibit is successfully used as an effective insulation, which does not require the use of additional materials. With its help erect not only load-bearing walls, but also partitions that do not insulate. This helps speed up the work and cut construction costs.

Varieties of sibit by brand

Sibit was invented a long time ago, but with the advent of new technologies, more modern blocks of various types and designs began to be manufactured. When building buildings, some of them are used. For example, the D600 is intended for the construction of houses with ventilated facades, it has high strength.

But the D500 is used for building monolithic buildings, while the D400 is a material for the construction and installation of a thermal insulation layer in the process of laying openings. D350 is used as a heater, but it differs fragility.

Classification of sibit

The dimensions of the sibit can be very different, but it is important to distinguish this material also from the variety. Thus, on sale it is possible to meet:

• Structural;
• Heat-insulating;
• Structural and heat-insulating products.

The structural ones are the heaviest and durable. The mark of their density can be from D900 to D1200. Structural and heat-insulating are reliable enough products, with the help of which it is possible to erect even a three-story building with single-layer walls. The thermal conductive qualities of this material make it possible to exclude the use of a warming layer in the walls. As for heat-insulating products, their density can vary from D400 to D500, they are considered the most common in the construction of internal partitions.

Dimensions and GOST

The size of the sibit can be very different, it all depends on the destination, which can be understood by name. For example, GB-100 are products that do not have grooves and ridges and have the following dimensions: 600 x 1000 x 250 mm. Thus, the volume of one block is 1.8 m ³ , for a cubic meter of such material it is necessary to pay 3,400 rubles.

The dimensions of the sibit can be 600 x 150 x 250 mm. If you have met such products, then you have GB-150, this option has a groove and a crest. The volume of one unit remains the same as for GB-100, the cost is also. Dimensions can vary up to 600 x 200 x 250 mm - if so, then you have the GBP-200 model, which has a groove and a crest. If you need a product with a groove, a crest, or a grip, then you can prefer the sibit, which is produced under the brand GB-300, the dimensions of this block are 600 x 300 x 250 mm, on sale you can find similar material and other sizes: 600 x 375 x 250 mm, as well as 600 x 400 x 250 mm.

If you have a sibit in front of you, the dimensions of the block are met to the nearest millimeter, then you can be sure that the product was manufactured in accordance with GOST. The companies that produce this material rely on the state standards of the Russian Federation under the number 31360-2007.

Dimensions of slabs

If you need floor slabs made of autoclaved aerated concrete, then you should choose the material manufactured according to GOST 19570-74. Such products are intended for floors of low-rise buildings, mansards, as well as cellars. The value of the support part of the panel is 120 mm with a possible error of up to 10 mm. Thus, you can purchase a plate, the dimensions of which are 2240 x 600 x 240 mm, and you will have to pay for it 2300 rubles.

Sibit (slabs), the dimensions of which are indicated in the article, can be purchased from companies specializing in this material.

If you are interested in a long length, you should pay attention to products with the following dimensions: 2740 x 600 x 240 mm. The cost of one such plate will be 2800 rubles. The last two parameters are considered standard, but the length can be changed. Thus, for plates in 3040 and 3240 mm it is necessary to pay 3090 and 3312 rubles accordingly.

If the length increases to the parameters in 3740, 4040 and 4240 mm, then you can purchase similar products at a cost of 3800, 4100 and 4320 rubles, respectively.

Not only a professional builder, but also a home master will be interested in the size of the sibit. The table presented in the article will allow you to make the right choice. The maximum size of slabs is 5940 mm, such a product costs 6040 rubles. However, there are intermediate values, which are equal to 5440 and 5040 mm, in these two cases the prices will be 5500 and 5112 rubles, respectively.

Reviews about sibite of different forms

There is a sbit, which is intended for the erection of load-bearing external walls and partitions. Such products are represented in the form of rectangular blocks. According to the builders, beams of reinforced aerated concrete, as well as blocks of ceilings, are used for the erection of ceilings. For the installation of door and window openings advised to use U-shaped blocks, which allow to speed up the work process and significantly reduce labor costs. Sibit, the size, the price of which is mentioned in the article, can be represented both in blocks of arc-shaped shape, as well as with crosspieces that facilitate the construction process.

Reviews about sibit features

Builders choose this material for the reason that it does not age and is not exposed to rotting processes. It is based on environmental natural raw materials, and the structure has many pores that make the walls breathable and warm. Sibit, whose block sizes are presented in the article, can not be deformed and exposed to fire.

The product is characterized by low thermal conductivity and allows economical use of energy resources. According to buyers, this material can be easily processed. The technology of production is considered quite simple, which is why the products are of low cost.

Conclusion

If you are going to use autoclaved aerated concrete for building a home, then you should be interested in the size of the sibit. Houses made of this material are frost-resistant, strong and have low thermal conductivity. Such characteristics they acquire through the processing process. Autoclave production is automatic, so it is possible to pre-set the desired properties of the blocks. Dimensions of the sibit, as mentioned above, are very diverse, so you will be able to choose the products of the necessary dimensions, which in the process minimize the need for processing, which will reduce the time spent on construction.