Construction goats: making and recommendations

Almost every builder who came up against the question of erecting a building for any purpose, wondered how to make the goats themselves with their own hands. Without them, the above manipulations will be quite difficult. The structure can be rented, however it is quite expensive, which is especially true for the case that involves building construction for a long time.

Preparation for work

If the goats are built by their own hands, then initially all materials and tools must be prepared. Among the first, one can distinguish a pipe, the diameter of which can be 1.5 or 2 inches. The final parameter depends on the expected loads. It will take a pipe with a diameter of 1 and 1.5 inches, the figure will depend on the pipe parameter, which was described above. From the blanks to be done horizontal jumpers, which will join the racks. Another 0.5-inch-diameter pipe will be needed to make the hooks into which horizontally oriented bridges are installed. A round rod with a diameter of 14 millimeters will act as pins. This piece must be welded on a horizontal jumper on both sides.

Additional recommendations for training

If the goats are built by their own hands, then in addition to the elements described above, an adjustment mechanism will be needed that will help level the surface irregularities. For its formation, you need to purchase four bolts, as well as nuts. Bolts should be selected according to the diameter, the minimum of which should be 20 millimeters. In the lower part of the pillars, you should weld the nut into which the screw is mounted.

Manufacturing technology

When the goats are made by their own hands, then it is necessary to start work on the formation of the whip construction from the racks. In this case, everything is quite simple, at the bottom of these elements you need to weld the nuts for the bolts. A branch pipe is welded in the upper part. It will need to be used to mount a section of the next tier. On the sides of the pipe top and bottom, having deviated from the edges of 200 millimeters, it is necessary to weld tubes, the length of which is 100 millimeters. Above and below them there must be four pieces. As a result, a cross should turn out, which will allow, by connecting the racks with crosspieces, to form a rectangular structure. Racks of the upper tiers will differ from similar elements from below by the absence of nuts. In this case, the pipe must remain free.

Recommendations for work

If you are building scaffolds, the next step along the edges of horizontal long and short bridges will need to weld the pins, bending them after this at a right angle. It is important to provide the structure with a rack, which must have components of thick boards. Their width should be equivalent to 0.5 meters. In the process of assembly, the rack is placed on horizontally located short jumpers.

Assembling

Producing scaffolding from metal, at the next stage it will be necessary to perform the assembly. To do this, the master is encouraged to enlist the help of another person. One of them will have to hold two racks, while the other will have to insert jumpers into them. With the help of short elements, you will be able to collect two sidewalls. Each of the masters, holding on to the side, begins to insert long jumpers. After the data of the workpiece is in place, you can even level everything by leveling the ladders on them. Before you make construction goats, you should familiarize yourself with the technology. At the next stage it assumes the possibility of installing subsequent layers, while using the above described technique.

Features of the manufacture of wooden forests

If you decide to make goats from wood, then the step between the posts can be equal to a limit of 2 to 2.5 meters. As for the width of the deck, it should be equivalent to one meter. Do not make the construction unnecessarily high, the maximum height limit is 6 meters. To carry out the work it is necessary to prepare boards with a thickness of 50 millimeters. As for their width, this figure should not seem less than 100 millimeters. It is possible to replace such blanks with a square beam of 10 cm. Round timber can form the basis of the pillars and supports. Spacers and fences, as a rule, are made of boards, the thickness of which is 30 millimeters or more.

Conclusion

If you want to make goats folding, which were discussed above, they can be used for many years. This can not be said about wooden structures that require processing with certain substances that provide material with special qualities. Wood serves less and is not so stable in the finished structure. Among other things, wooden wheels should be installed on a special stage, which excludes the interaction of the timber with the ground. Drawing construction goats will allow you to carry out work without errors. You can borrow it from the article or draw it yourself, depending on the dimensions of the future building. After all, it will depend on how convenient it will be to build works.