Vinyl: sticking car

Vinyl is a film made of polymers. If necessary, this material can be easily applied to any body elements, as well as the interior. Typically, the film performs protective functions, protecting the surface of the vehicle from minor mechanical damage. But these are not all properties that vinyl possesses. Pasting the car with this material allows you to refresh the appearance of the body, as well as create an original picture on it.

Film functions

So, what does vinyl give? Pasting of the vehicle with this material:

1. Protects the car's surfaces from corrosion and scratches, and also prevents the burning of the coating.
2. Allows just a few days to change the texture or drawing. In this case, the paint and varnish coating of the body will not suffer.
3. Allows you to create an art composition and apply almost any picture to the surface of the vehicle.

Material Advantages

The popularity of the film is easy to explain by its virtues. Pasting with auto vinyl is a common type of tuning. Among the advantages of this method is:

1. The technology of pasting a vehicle with a film is quite simple. If you want, you can do all the work yourself. At the same time there is absolutely no need to buy modern and expensive equipment.
2. Vinyl film can be easily removed if necessary. Thus it is possible not to worry for a paint and varnish covering of a body. Its integrity is not violated. This indicates the reversibility of the process.
3. Relatively low cost. Many car owners will agree that airbrushing is a very expensive procedure. And the usual painting does not cost cheap. Vinyl also allows you to update the appearance of the vehicle, while saving a significant amount.

Technology of pasting

So, how to apply vinyl? Pasting a vehicle with a film is a simple process. The main advantage of this type of tuning is its ease of operation, as well as minimum requirements for surface treatment. At this stage, no special costs are required. It is enough to wash the vehicle thoroughly, degrease and wipe dry. If there are small chips or scratches, they are recommended to be closed. Otherwise, bubbles with air will appear in their place.

After preparation, you can apply vinyl. Pasting can be done in several ways: wet and dry. The latter option is not suitable for beginners, since the glued material can no longer be corrected or torn off without damaging it. It is best to glue in a wet way. In this case, the surface of the body is wetted, and only then the film is applied on them.

Glue vinyl is one piece. Begin with the details with the smallest radius. It will allow to stretch the material without any difficulties on the whole surface. Also, many specialists practice the pasting of the salon with vinyl. At such kind of tuning it is recommended to remove all details which can stir.

What you need to work

Pasting a vinyl vehicle takes a little time. However, for carrying out such work, tools are required. What is needed?

1. Magnets or paint tape.
2. Knife clerical.
3. The rag is dry.
4. Combined, plastic and felt squeegee.
5. Degreaser is ethyl alcohol.
6. Industrial dryer.
7. Sealant sealant.
8. A sprayer filled with soapy water.

Preparation

Vinyling is done in several stages. The first step is the preparation of the vehicle. Carefully washed car must be dried, and then wiped with a degreaser. After that, you can start fitting. At this stage, you must be very careful. It is worthwhile to carefully measure everything, and only after that cut. It should be remembered that more material is used for bends and corners. All the necessary labels on the body can be made with paint tape. After all the measurements and adjustments, you can cut out pieces of vinyl.

Pasting of a vinyl machine

If you decide to resort to a wet method of pasting, then it follows from the sprayer to moisten all surfaces of the body. Only after this, you can proceed to the main stage of the work. Before applying the vinyl, it is necessary to spread it on a flat surface and remove the substrate. At the same time, care should be taken to ensure that debris and dust do not get onto the adhesive. Formation of folds is also undesirable. So it's worth using someone's help.

After the material is applied to the surface, it should be smoothed. It begins with the middle of the canvas, gradually shifting to its edges. At this stage it is better to use a rubber squeegee. In the process of smoothing, the film must not only be smoothed, but also heated. In this case, it is better to use an industrial hair dryer. The temperature of the air flow should not exceed 70 ° C. Otherwise, the film will begin to break down.

Pasting with vinyl should be done carefully and without haste. Do not allow the formation of air bubbles and wrinkles. On the bends, corners and convex parts, the material should be heated more thoroughly. After all, the vinyl should be stretched evenly. The edges do not need to be bent.

In conclusion

After the car is completely covered with vinyl, it is necessary to dry all surfaces. Now the vehicle should stand for about 20 minutes and cool slightly. Finally, all surfaces should be passed with a felt squeegee to remove the remaining bubbles. Excess material should be carefully trimmed. In this case, it is necessary to leave a margin of 1 centimeter at the edges. Bending the vinyl, you should thoroughly warm it up. In the end, all edges should be treated with edge sealant. A few days old car should stand in the garage. It is also not recommended to move on it at high speed for 10 days.