Timber imitation

The houses from the timber look very attractive, but if you own another type of building, you can sew it with imitation of a bar. This decoration has been enjoying popularity more and more recently. To produce it, an array of high quality wood is used. This cladding material is a wooden panel, which is more affordable in comparison with the natural counterpart.

Why choose a simulation of the bar

The lining has a low weight, which facilitates transport and installation. The imitation of a beam for finishing not only outside, but also inside premises is used. Installation work involves the docking of products closely, intermediate grooves are not formed.

This material has high strength, it is durable, resistant to climatic factors and other corrosive media. This decoration allows you to make the walls more warm and soundproof. And if you additionally use a layer of insulation, then you will make your home resistant to wind and frost.

Preparing the panels

Sheathing by imitation of a bar assumes the preparation of panels. They are realized packed in a sealed film, because under the conditions of the plant they are subjected to chamber drying, so that the wood does not absorb excess moisture from the air. Before the beginning of finishing works, the products are removed from the package and left for 2 days in the environment where they will be used. Otherwise, the geometric dimensions of the panels may change - the finish will be skewed.

The next step will be the treatment of wooden panels with antiseptic substances. It is much easier to do this until the time of installation, and technical locks will not be available after that. If the panels are not painted yet, then at this stage they are covered with a layer of varnish or any other selected composition.

On the features of laying waterproofing

Sheathing of the house by imitation of a bar can not do without the laying of a waterproofing layer, in the quality of which PVC-film or parchment can make. Fasten the material directly to the wall. Cloths with each other are covered with a overlap of 15 cm. Joints should be glued with aluminum tape.

For additional strength to the wall, the canvases are attached using a construction stapler. It is important to ensure that the waterproofing does not sag, however, it is not worth it to pull it too tight. This recommendation is due to the fact that the film can tear as the temperature changes. Do not be afraid that the waterproofing will depart from the surface of the wall, because it will be pinned crate.

Recommendations for installing the frame

Sheathing by imitation of the beam by her own hands necessarily provides for the installation of a lathing sheath. If the wall is flat, then for this purpose a beam of wood with a square cross-section in the range from 30 to 50 mm is used. For curved walls, a metal profile with mounting brackets is used. Mount the crate to the wooden walls recommended 40-mm self-tapping screws. The pitch of the lath usually depends on the parameters of the insulation, but a fairly thick imitation of the bar has an impressive weight, so for outdoor applications, the distance between the elements should not exceed 60 cm.

For internal works, this parameter can be 80 cm, because the panels will be thinner not only in thickness, but also in width. In addition, their weight is much less. The sheathing of the house from the outside with imitation of a bar may imply the existence of two systems of a shed. The first in this case is installed horizontally.

Recommendations for laying insulation

Insulation is needed only with exterior decoration, this difference is the main in the technique, which involves the installation of the material from the inside. This stage allows you to move the dew point and make the walls warmer. It is necessary to arrange the insulation against the crate. Unfilled areas should not remain, joints should be as tight as possible.

Sheathing by imitation of the timber from the outside can provide for the laying of the insulation in 2 layers. The number of layers will depend on the climate in the region of work, as well as on the targeted use of the house. Mount the heater can be fungus or tape. Acquiring matte thermal insulation, you should remember its standard width, which is 60 cm. As for the foam, this parameter is 1 m, so the canvases will have to be cut.

Cladding technology

The lining is simulated by a certain algorithm. Install this decoration can be on the walls of different materials, namely:

• Logs;
• Bricks;
• Concrete.

After the completion of the work, the walls will look like those that are made of natural timber. Installation work is not difficult. Profiles are complemented by grooves and spikes, which allows them to fit tightly to each other. The boards are fixed horizontally. Sheathing by imitation bar allows the use of a universal material, which is combined with a profiled or glued beam.

Quite often recently you can meet baths and rooms of houses, which are lined with such material. If it comes to exterior decoration, then the products can be used on the walls of buildings made of foam blocks, carcass and concrete. Fixation is carried out on the lath, which is performed in the form of bars. Elements of the frame are located along the entire perimeter of the walls, the distance between the slats should be approximately 50 cm.

For the reason that the imitation of the beam is fixed horizontally, the fixing of the bars should be carried out vertically with the help of self-tapping screws. In order to make the walls warmer, you can also lay a thermal insulation of natural materials, namely ecowools or mineral wool.

Sheathing by imitation of a beam assumes fastening of one more layer of a waterproofing over a crate. Then you can start installing the cladding. The installation should proceed from below, it is there that the casting board is fixed. Place the products with a comb up. Screws are screwed into the spike of the board, the hat is recessed by 2 mm. When laying the next board, you must position it with a groove in the spike and adjust the items to each other. At an angle of 50 °, a screw is driven into the spike. The last row is set on self-tapping screws. The places where the fasteners were installed can be sealed with nails and sanded. After the completion of the installation work, proceed to the puttying and painting of the beams.

Inner imitation lining

If you have decided to use imitation of a bar for interior finishing, then the technology described below is to be guided. For such work, it is recommended to level the walls so that the space of the room does not decrease too much. The surface is cleaned of dust and dirt, and then a layer of vapor barrier is installed on the wall.

Next, the crate must be made of material, which is chosen taking into account the specifics of the room. The lining is installed vertically. On concrete and brick walls, the installation is carried out using dowels, in the case of wood it is possible to work with self-tapping screws.

If the skin is imitated by imitation of a bar inside the premises, the conditions of which are characterized by high humidity, the elements for the carcass must be treated with an antiseptic. In addition, it is possible to use a galvanized profile for wet rooms. The panels are installed horizontally. The method of fixing them is similar to that used for finishing the facade. Klyaymery can be used as a fastener, but for the ceiling this approach is not reliable. It is better to use small carnations or self-tapping screws. They are clogged or twisted into a spike at an angle of 45 °.

Conclusion

Sheathing of walls by imitation of a bar does not presuppose fastening of products by a face-to-face method, if the work is carried out indoors. This is due to the fact that hats because of the small thickness will be very difficult to hide. When connecting panels in corners, you should apply internal and external corners, they are usually implemented together with the finish. After the completion of the work, the walls can be sanded and the tinting varnish applied. The ceiling is usually sewn on already painted panels, this simplifies the work.