Scorpion from beads: sketch, scheme of weaving. Bead Lessons for Beginners

Beading is an exciting and interesting activity. There are a lot of ways and variants for creating various figures of animals and insects. For example, a scorpion from beads - the work is not so difficult to perform, it is quite possible for a beginner master.

The material of the article is aimed at the accompaniment and detailed explanation of the moments in which complexity or difficulty in the process of work may arise. Lessons of beadwork for beginners are more productive to pass on simple and simple tasks. Follow the chronology of the description and do everything slowly, carefully studying the sequence and features of the work.

Scorpion from beads

The scheme of weaving to make a scorpion is quite simple in its execution.

The length of the wire, which will later be used in the process of work, should be at least 150 centimeters. The made scorpion from beads will be created with the help of a large-scale weaving technique.
Tiers of beads are divided into two levels - the upper and lower. The upper part is the back of the scorpion. Accordingly, the lower tier will form a segmented elongated abdomen of the insect.

Your task is to understand correctly how scorpion is made from beads. Sketch of the future product is a key part in the course of work. Using the outline on paper, you mark out the number, position and color of the beads.

If you are using a description of a ready-made set, then the drawing is not needed. Proceed directly to the assembly.

Required materials and tools

Before you start learning bead lessons for beginners, you will need to prepare the following materials:

• Beads of various brown shades (brown);
• Black beads;
• Beads of yellow or orange colors - for the eyes;
• For the firmware - thin line;
• Wire diameter of about 0.2 millimeter.

Some recommendations

Beads in the weave are desirable to use a large size. Colors can be chosen at your own discretion and taste. Most often for braiding scorpions use beads of brown, red, yellow, orange and gold. But you can use any other colors and shades, thereby giving your product its originality and originality.

Scorpion: sketch of beads and assembly sequence

First row

• Dial the beads on the wire in the following sequence: one black, two brown and again one black. Then three brown beads. They form a tier, which will be located from the bottom. Assemble the collection of beads in the middle of the thread.
• The end of the wire on which the black bead is strung, pass through three beads of another shade from the opposite side of the base.
• Procratching should be tightened. The bottom and top balls of the first line were obtained.
• The next step is to work on the scorpion claws. On the thread, put on five black beads and eleven beads of another shade.
• Pass the end of the thread through four black beads in the opposite direction. In this case, the last bead must be held.
• Tighten the wire.
• At the same end of procrastination, type five beads of the same color.
• It is necessary to hold the final bead and pass the wire in the opposite direction through the four beads. Next, pass the thread through eleven beads of a different color.
• Tighten the thread. Beading of the scorpion claw can be considered complete.
• Similarly, you need to make a second claw.

Second row

• First you need to do the first level. Put the beads on the wire in such a sequence: one brown, two yellow, one brown. After that, pass it through the previously dialed beads. Wrap the wire so that the beads are located parallel to the upper ball of the previous line.
• For the lower level, you need to use five brown beads. Bend the thread so that the beads lie parallel to the upper ball.

Third row

• For weaving the upper tier you need to take six pieces of brown beads.
• For the legs you will need to dial eight beads of another shade at one end of the wire.
• The most extreme should be kept. At the same time, pass the same end of the base through seven black beads in the opposite direction.
• Tie up the wire. You should have a foot.
• Applying the other side of the wire, weave another foot.
• To create a tier at the bottom on the third line, you need to apply six brown beads.

Fourth row

• Weave six brown beads for the top ball of the craft and the same for the level that will be placed below.

Fifth row

It is very similar to the third row.

• It is necessary to make a tier, which will be located on top, of brown beads - 6 pieces. Next, weave the legs of 10 black beads.
• The bottom line is weaved from 6 brown beads.

Sixth row

The scheme of formation of this line is similar to the previous series.

• Weave the top of the six brown beads.
• Next, make the feet. To make each of them you need 12 black beads.

Seventh row

• The row, which is placed on top, has six brown beads.
• For the lower tier you need six beads of the same color.

Eighth row

• It will take five brown beads for the top of the scorpion and four beads for weaving the bottom.

Ninth row

• It will take four beads of brown color to weave the upper tier.
• For the bottom row, you should use beads of three similar colors.

Tenth row

The scheme is the same as in the ninth row.

• To create the top line, use three brown beads.
• The lower tier also needs three beads.

Eleventh row

• The upper tier is weaved from three brown beads.
• For the weaving of the lower level, you will need two beads of the same color.

Your bulk weaving from the beads of the scorpion is almost complete. Let us proceed to the second part.

Sketch of tail manufacturing

In the process of manufacturing the tail part, it is necessary to use the technique of conventional parallel weaving. Lines should be placed one after another.

Weave five lines of two beads. Next, five respectively one black bead.

Thread the thread in the following way: pass it through the previous line, twisting together the two ends of the base.

Last step

In the final it is necessary to sew the product with a fishing line. Tighten to make the scorpion of beads hold shape.

Use the usual firmware.

As a rule, beadwork is obtained practically from all, provided that the technique of work is observed. With the accumulation of skill and knowledge, the consumption of time will subsequently be considerably reduced. The acquired experience will give the chance to create absolutely new and original products from beads.