HobbyNeedlework

How to weave a thick bracelet of elastic bands: instruction, photo

Anyone interested in how to weave a thick bracelet made of rubber bands, the following detailed instructions on making dense, multi-layered ornaments from the famous rubber bands "Fanny Lum" will be useful. If desired, you can always take any of the described methods of weaving and develop on its basis its own line of man-made jewelry.

Bracelet "Buton"

Rudders and craftsmen are likely to be interested in information on how to weave very thick bracelets made of rubber bands and at the same time make them very beautiful, stylish and fashionable. As you know, the trend never leaves the trend - try yourself to make an amazing chain of large round buds. Such an ornament can be worn as a bracelet, and as beads, and even as a belt.

To create a delightful chain of buds, you will need green and red "Fanny Loom", a clip, a hook and a small machine "Finger Lum".

How it's done

  • Throw two opposite columns of two green rubber bands, twisting them with a figure eight.
  • Top two pairs of red "irises" in pairs on top of each other.
  • Discard the green rubber bands in the center of the machine "Finger Lum".
  • Put on, without twisting, on all four pegs green rubber.
  • Throw off all the red gum in the center.
  • Throw, without twisting, on all four columns one more green "iris".
  • Throw off the bottom green rubber bands in the center.
  • To finish the work, discard the green loops on two bars and fasten the chain with a clip.

If you want to learn how to weave a thick bracelet out of rubber bands in such a way that the buds become bigger and bigger with each step, repeat the second step three times, throwing out the rubber bands of different colors and dropping the lower "irises" into the center.

Bracelet "Wave"

This decoration consists of two different colored layers. To understand the stages of its manufacture, the instructions presented will help you.

How to weave thick bracelets of rubber bands, if you have not bought a single machine? Strangely enough, for making the most effective ornaments from elastic "irises" you do not even need a machine - just a good hook.

So, for the summer bracelet "Wave" you will need black, orange, yellow and light pink rubber bands, as well as a clip and, of course, a hook.

Beginning of work

  • Throw on the hook a black rubber band, twisting it with a figure eight. Pick up the instrument with two more black "Fanny Lum".
  • Drop all the hinges on them from the hook. Also hang the hinges on the hook.
  • Pick up the instrument with two more black "irises," drop the loops on them, but now leave the rings formed on the finger.
  • Throw on the hook three yellow rubber bands.
  • Dump the hinges from the finger to the hook.
  • Repeat the previous steps until you get the desired length of the decoration. In black hinges on the hook, thread the clip, then remove them from the instrument.

Second layer

If you already know how to weave a thick bracelet made of rubber bands (the scheme of two-layer ornaments, by the way, is quite simple), you probably already know that the first stage of making jewelry was only the creation of a primary workpiece. Now you can proceed with the end of the bracelet.

  • Turn over the resulting workpiece and pounce the first double black loops on the hook.
  • Fit three yellow rubber bands from the workpiece and twist them with a figure eight.
  • Pick up the instrument with two black "Fanny Lum".
  • Discard all the rings from the hook, then put the hinges on it from the finger.
  • Repeat the previous steps until the end of the workpiece.
  • Dump two double loops on your finger, holding one through the other. In the resulting loop, thread the clip.

Double-sided bracelet

How to weave a thick bracelet made of rubber bands, if you want to make in it not just two layers, but two faces? It's very simple - follow the instructions of enthusiastic needlewomen, and you will definitely succeed.

To make a bilateral decoration, take white and multi-colored rubber bands, a clip and an ordinary hook.

First step

  • Throw a blue rubber band on the hook, twisting it with a figure eight. Pick up the instrument with two lilac "Fanny Lum".
  • Drop all the hinges on them from the hook, then again pick up the two lilac rubber bands.
  • Throw off all the hinges without dropping the ring from your finger. Throw a white "Fanny Lum" on the hook.
  • Slide the rubber with your finger onto the hook. Pick up the two yellow "irises."
  • Discard all the hinges on them from the hook, without ripping off the ring from your finger. Put a white "Fanny Lum" on the instrument. Rub your finger off the finger on the hook. Repeat the previous steps until you get the correct length of the chain.

What's next?

Interested in how to weave a thick bracelet of elastic bands, it will be interesting to learn that the creation of such an ornament does not consist of one or even two, but of three full stages. So:

  • Weave in the technique of the basic pigtail six blue rubber bands.
  • Fit a white elastic band from the resulting blank.
  • Pick up the instrument with two blue "Fanny Lum". Discard all the loops on them, then repeat all previous steps.
  • Throw a hook on the white rubber from the workpiece. Pick up the two yellow "irises."
  • Discard all the hinges on them from the hook and continue the weaving in the same way to the end of the workpiece, each time changing the color of the rubber bands.
  • Secure the loose loops with clips.

End of work

The second side of such a bracelet is padded on the same principle as the second layer in the decoration called "Wave". Once you have processed the entire workpiece, it will be necessary to remove the clips, reset the loose loops from the hook, weave the base chain of the five blue rubber bands and fix the main clip.

Now you know how to weave thick bracelets made of rubber bands. The photo will help you to orient yourself in how to look like finished products made from popular "Fanny Lum".

Similar articles

 

 

 

 

Trending Now

 

 

 

 

Newest

Copyright © 2018 en.birmiss.com. Theme powered by WordPress.