How to make a bailer with your own hands?

The borehole for the borehole is the simplest and most efficient design. At the same time, it does not require any special tools or equipment for its manufacture.

What is a bailer?

In order to build the presented construction, you must first understand what it is. So, the bailer is a special device that is used to drill wells in a rock-and-wire method. In addition, with the help of such a design, it is possible to clean the channel when it is filled with rainwater.

It's not so difficult to make a bailer with your own hands. It is necessary to begin with to understand its design and to pick up all materials and tools necessary for work. Most often used such an adaptation during the construction of private houses or villas, where it is planned to build a well.

Advantages of the presented device

It should be noted that this design has certain advantages:

- ease of use;

- quick and easy manufacturing;

- efficiency;

- the ability to independently implement the process;

- economy.

In any case, the bailer is considered to be the simplest tool for producing wells. To work with this design, only 2 people are enough.

Product design

Before you make a bailer with your own hands, you need to understand what it is made up of. So, the main parts of the design are:

- a piece of hollow pipe equipped with a non-return valve that is capable of retaining sand, clay, or other rock;

- impact cartridge;

- a rope that is attached to a piece of pipe (with this element you can pull the glass back to the surface);

- Construction on three or four legs, to which, in fact, the pipe is attached.

Principle of operation of the unit

Before you make a bailer yourself, you need to understand how exactly this device works. So, the pipe on the long cable should be lowered into the bore hole. Then it should be raised at least 30 cm up and released. While touching the pipe with the ground, the ball inside the glass jumps up and opens its lower opening. At the same time, water enters into the pipe mixed with sand or silt.

Then the ball goes down and presses all the mass that is inside the glass. Now the pipe can be slowly and smoothly pulled out of the hole. At a time from it you can reach up to 0.5 kg of sand (silt). Then the actions are simply repeated several times. Gradually, you continue to work until you reach the required depth.

Materials and tools required for work

Trough for the well with their own hands is very easy. Naturally, you first need to pick up all the necessary tools and material. So, you can build a structure from improvised means or buy the necessary items in the store. If before the construction of the well you were engaged in erecting a house, then there will be no problems with the materials.

Most often for the construction of the structure is used:

- a pipe, the length of which is about 80 cm. Its inner diameter must not exceed 60 mm;

- a metal cable;

- a child's ball made of PVC or rubber (or a metal ball), whose diameter is about 4 cm;

- washer with a flat surface;

- metal grating.

Before you make a bailer with your own hands, try to prepare a welding machine, with which you will need to connect all the parts.

The process of constructing

It should be noted that for the construction of the presented structure it will not take much time. Zhelonku with their own hands can be done in just a couple of hours. All the work involves several stages:

1. To the bottom of the prepared pipe, it is necessary to attach a thick washer by welding, which will serve as the bottom of the bailer. The saddle of the hole should ideally fit the diameter of the ball, which will fit inside the glass.

2. A small obstacle should be made at the top of the pipe. It will not allow the ball to fly out of it. To do this, you can weld a small piece of metal mesh or lattice. In addition, the upper part also needs to make fasteners, which will fix the cable.

3. Next, making a bailer with your own hands is easy. Now the cable is attached to the pipe, and a construction is being constructed, to which its second edge will be attached. The height of the bailer depends on the depth of the well, which must be done or cleaned.

In principle, these are all the actions that need to be taken to build a structure.

Features of drilling wells

Before you make a bailer, try to figure out how you will work with it. If you need to make a drilling process, then note that this device can only be used on loose and loose rocks. It should also be borne in mind that the presented method of producing a well (cable-impact) does not imply subsequent washing of the channel. Therefore, such a method is best used at the last stage of drilling.

It should be noted that using a bailer is not a very productive way of building wells. However, many builders recognized it as safe as possible. In addition, drilling a bailer is a life buoy in the event that a well has to be built on quicksand.

In order to make the work easier and faster, you can periodically pour water into the well, which will make the soil more loose and supple. If the soil is solid, then this method of drilling is not effective. The pipe will additionally rammed it.

Features of cleaning the well with a bailer

If you once discovered that your water channel is clogged with sand or silt, then, naturally, it is necessary to punch it. The best equipment for this is the bailer. Of course, this process requires considerable force, but it is the first one in terms of efficiency and safety. In addition, you do not have to spend electricity or rent expensive equipment.

In principle, the cleaning process is the same as well drilling. Naturally, before starting work, you need to find out the cause of the clogging. If you just clean the channel, then after a while it can again clog. Naturally, you need to eliminate the causes of the problem.

Clearing a well with a bailer has one advantage: how well the channel worked before starting the work does not matter. For the presented procedure it is better to take a long piece of pipe (about 1 m). Further, the shock method removes all the accumulated dirt, silt and sand from the well.

Thanks to this design, you will be able to bring back to life a completely clogged well, which could not be cleaned by other devices. A submersible pump can be used to completely clean the channel. With this device you can pump the water until you have a crystal clear liquid. Now you see that the bailer for the borehole is made and used very easily.

In order for the well not to get dirty again, you can repeat the procedure periodically. Please note that you should not forget about the measures that contribute to the prevention of clogging the channel. Now you know how to make a bailer with your own hands, as well as where and how it is applied. Good luck!