How to close loops on an elastic band with knitting needles? This is not very difficult

When beginners knitters create their first products, at the very end of their work technical questions arise. How to close loops on an elastic band with knitting needles? This seems to them an insurmountable difficulty, because in no scheme is it explained in detail how to close the last row with spokes, because the circuits are a drawing that not everyone can understand.

Close the hinges. Method one

So, the first work is almost finished. The only thing left to do is close the last row. How to cover the loops on an elastic band with knitting needles will be described below.

First option. First you need to pay attention to the thickness and friability of the yarn. Only then it will be possible to understand how tightly tighten the loop, so that in the end a very even pigtail is obtained. This way you can use when knitting any pattern of any detail. Then the edge will not stretch.

It is necessary to stretch one loop through the other in turn. So it turns out one loop. Together, we must immediately tie the first and the edge of the eyebands viscous, taking up the rear wall of the loop. So it turns out a loop, which must be translated from the right spoke to the left, then viscous viscous to tie it together with the next and again behind the back walls of the loops. So it is necessary to tie the whole series.

When the last stitch remains on the spoke, the thread must be cut off. Put it in a loop, leaving about four centimeters, and tighten. In order not to tighten the loop, you can apply a short hook. But if it is with knitting needles, this article will help to cope with the task.

If the knitting is made from the wrong side, the edge loop must be knit with the back straps. Through the second loop you need to tie the first one. In exactly the same way, one loop should be sequenced in sequence. Through the received loop, the previous one is sewn. Repeat all the same way until the loop ends. At the end, the thread must be cut off, and its tip stretched through the last loop.

Close the hinges. Method of the second

If the knitter applies this option, you can get a special edge, similar to a pigtail, which is stretched. How to close the loops while knitting with rubber bands? It is this option will do the best.

As a rule, so close the gum, regardless of the number of facial and purl loops and relief patterns. Apply this method to any pattern.

On the right knitting need to wear the first loop, the second knit the front or the back. So it turns out two loops on the right. The second loop should be stretched in the first, which is on the right spoke. So knit to the end of this series. When only one eyelet remains on the left-hand spoke, it should be left about four centimeters, cut off the thread, insert it into the loop and tighten.

The third way

So, how to close the loops on an elastic band with knitting needles? This option is called "Jenny's method" - by the name of the one who invented it.

The first loop of the row is removed on the right knitting needle. Make the collar of the next hinge, according to what it is for the loop (front or back), then throw the previous loop with the collar. Now you can remove it from the knitting needle. Repeat as many times as necessary until the last loop is left on the spoke. The thread is cut off, you just need to leave a small tip, which should be pulled through the loop, which is left. The thread is fixed.

"Collar" for facial loops: thread the working thread to your right knitting needle (this will be in the opposite direction from the usual cape), the next loop to knit the front, then it is necessary to raise the cap over the tied face loop and throw it from the knitting needle into a loop that has already been knotted . "Collar" for the purl loops: throw the working thread from itself to the right knitting needle (as with the usual cape), the next loop must be sewn on the wrong side, then gently lift the cap over the back loop, which is already tied, and throw it from the knitting needle into the loop.

Elastic band 1x1

Read on to understand how to close the loops of 1x1 rubber bands with spokes.

Knitting is in the left hand. With your right hand, take the right needle, it is inserted into the edge loop from left to right, removed from the left knitting needle, without tying. The next loop to bind the front. On the right there are two loops. Insert the left spoke in the first loop from left to right, slightly stretching it to yourself; With the right needle, extend the second loop through the first. Now on the right spoke there is only one loop. Next on the drawing is a purl loop, which must be tied with the usual purl. And then to do as before - to enter the left spoke into the first loop from left to right, and right to extend the second loop through the first one. So do until the end of the series. The last edge should be tied with the wrong one and stretched through the previous one. The resulting loop is stretched wider, cut the thread, thread the tail of the thread through the loop and tighten.

Eraser 2x2

Find out how to close the loop of a rubber band 2x2 with spokes, you can just below. This is done with the help of a needle, but we will consider the option with spokes.

Through the first loop of the right needle, extend the second, using the tip of the left. Thus, the elastic band will be elastic. The next loop to tie the purl, beforehand passing the thread before the canvas. With the tip of the left knitting needle, grab the first one from the right loop so that the second one can be pulled through it. Similarly, knit to the end of the row each loop, following the pattern of the gum. In the end, cut the thread and hide it in the last loop. It turns out an elastic and even kromochka.

The fourth way

How to close the loops of English rubber bands with knitting needles? It is not difficult to do this even for beginners. This option is suitable for the aforementioned rubber, and even for the pattern. Apply it in the event that you want to get the edge of the part, which will stretch well. This concerns, for example, the loops of the round neckline "under the neck".

You need to tie off the edge with a double thread. Then throw it on the left knitting needle. They must be tied together with a subsequent loop. If it's facial with a crochet, then it is necessary to tie everything together - the edge, facial and the nakid with the facial. If the second loop is wrong, you must knit the purl. The right spoke now has one loop. It is necessary to transfer it to the rest and to tie it along with the subsequent one. Similarly, close the hinges on the entire row.

If such a detailed description of how to close the loops on an elastic band with knitting needles is not enough for someone, you can see the video in open access. But, as a rule, even a beginner knitters can be quite a few prompts. So, everything will turn out!