Duck drinking bowl by own hands: manufacturing

If you decide to have a ducklings, then it is necessary to think about what kind of drinkers will be on the territory. The simplest options are buckets, basins and bowls. But such containers have drawbacks, among them one can single out rapid water pollution due to bathing of the bird, which will inevitably lead to the need to change the liquid and wash the container. Light open containers of small volume can be used exclusively for small fragile chicks, which are not capable of overturning the structure. A more suitable solution will be an auto-drinking machine, the dimensions of which should correspond to the number and age of ducklings.

Manufacture of nipple drinkers

If a teaspoon drinking bowl for ducklings is produced by hand, then it can be done using the technology described below. This design is also called nipple. It can be called one of the most complex, but at the same time, convenient.

Preparation for works

A nipple for drinking ducklings can not be made by hand without a square pipe, the side of which is 2.2 cm. You should choose a workpiece that has internal grooves. It is necessary to consider the length when buying. The smallest distance between nipples should be 35 centimeters. The nipples themselves will be needed. If the bird has already grown a little, then you need to buy nipples 1800, which work on the principle of "up and down", whereas for small ducks, a 3600 nipple, which works all 360 degrees, is suitable.

You need a muffler for the tube, a drip pan or a micro-bowl, and an adapter, the latter of which is needed to connect a round and square tube. If you do not plan to connect the drinking tank to the water supply, you need to buy a water tank and a hose.

Preparation of tools

Before you will make a drinking bowl for ducklings with your own hands, you need to take care of the presence of a drill and a 9-millimeter drill. A conical tap is required, which is useful for threading. For lack of these tools and materials, you can buy them in the store of the corresponding goods.

Technology of work

If a drinking bowl for ducklings is produced by hand, the pipe will initially have to be planned for drilling. A hole of 9 millimeters is made in these zones. A tap will allow to cut a carving where then it will be necessary to wind nipples. At one end of the tube, you need to install a muffler. Next, take the vessel, where the liquid will be. It is best to use a tank made of ordinary transparent plastic. It should have a lid.

In the process of making a drinking duck for own hands, the photo of which is presented in the article, it is necessary to make a hole in the tank, placing it in the bottom. Its diameter should correspond to the diameter of the discharge hose. There may be threaded, as an alternative, you can simply install the hose. The joints obtained are wound with a Teflon tape, as well as other places that can become a source of leaks.

Features of work

In the process of manufacturing drinking bowls for ducklings by own hands, a photo of which is in the article, microtubes are located under the tubes. This applies to the pin for 1800. If you select a parameter in 3600, you will need to install drift eliminators. The tube with the teats is fixed horizontally, it is important to take into account the height, which would be convenient for the chicks. In the next step, the container is installed above the pipe, which is equipped with nipples. It is recommended to install all this indoors, since the liquid can freeze. Before you make a drinking bowl for your own hands, it is recommended that you stock up on the heaters for the aquariums. They use specialists when there is a possibility of freezing water at too low a temperature.

Making a vacuum drinker

If you make drinkers and feeders for ducklings with your own hands, then you can take as a basis the technology of vacuum construction. It will be somewhat easier compared to the above. To do this, it is important to stock up several items, among them an ordinary 1.5-liter plastic bottle. It will take a small vessel, which is a pallet. You can buy it in the store of the relevant specification.

With a wire frame or metal profiles, the bottle should be fixed to the wall. Water is poured into it and the cork is twisted. The bottle should be placed in the frame, placing the bottom on top. The pallet is placed under the bottle in such a way that some space remains between the neck and the bottom. In order to avoid pouring out water, the sides of the pallet should be above the neck. After that, the lid is removed, which allows the user to use the drinker for the intended purpose.

Conclusion

If you need a drinker for small ducklings, with your own hands this design can be made quite simply. Do not save time or effort by simply installing a large container of water. Still not strong chicks can express a desire to swim, however such actions on their part do not always end successfully. A bird can catch a cold and even drown. Therefore, it is recommended to make drinkers on their own or purchase a factory-made device in the store, this will be the best solution, since the finished product will last for many seasons.