Decorative brick by yourself: instruction and material

When decorating rooms for different purposes, you can use decorative bricks. However, if you are full of enthusiasm and imagination, then you can perform such products yourself, because the purchased options are not always able to satisfy the consumer with appearance and cost. With the help of this finish, you can bring a unique charm to the interior. In the process of work, different raw materials can be used, sometimes gypsum is used for this, sometimes cement.

Form preparation

If you decide to perform decorative bricks with your own hands, you should start working with the preparation of the form and some tools, as well as materials. The master should take care of the availability of:

• Cardboard boxes;
• Fine wire mesh;
• Containers for mixing portland cement;
• Rubber kitchen gloves;
• water;
• Dishes for dye;
• Dye.

Mix preparation

When doing decorative bricks with your own hands, it is important to properly prepare the mixture. To do this, you need the balls of polystyrene, white Portland cement and fine sand. For one serving, one part of the cement and three pieces of sand will suffice. Once all the ingredients have been prepared, you can begin to mix the mixture. For this purpose, polystyrene balls are poured into the container, then portland cement and sand are separately mixed. In small portions, water should be added. The mixture in the end should not get thicker than sour cream.

If you decide to make a decorative brick from polystyrene with your own hands, then in the next step the resulting mixture should be poured into the beads of foam, after the composition is well mixed and spreads into shapes. When the mixture begins to dry, it can be given the desired shape, after removing from the cells. It is important to take into account that with increasing time to dry it will be more difficult to give products corresponding to bricks look. That is why it is important to try to keep within one day.

Application of dye

Once the decorative brick is ready, you can proceed to the last step - applying the dye. A cement mortar is applied to the surface of the products, the thickness of the layer should be 1 mm. Portland cement, quartz sand and water are mixed for this. After the composition dries, it can be applied to the acrylic dye. Before application, dilute it so that a little more tinted water appears. Application should be carried out in two or three layers. Then the brick should be left to dry completely.

When making decorative bricks for interior decoration with your own hands, it should be protected from staining. To do this, experts recommend the use of sealants based on cement. The application can be carried out by spraying, sometimes an ordinary brush is used.

Recommendations for the manufacture of gypsum decorative bricks

To date, we know a huge number of technologies for making gypsum decorative bricks. Some masters add to the composition glue, limonku and lime. However, if you want to use a classic recipe, you need to mix water and gypsum. To make such a brick, too, you will need the availability of molds. It is better if they are made of silicone. More expensive are the forms of polyurethane, they are suitable for making bricks from gypsum and cement, because they are able to withstand alkali.

In the process of making gypsum brick, you will need a capacity that must be made of plastic, because this material is easily laundered. Decorative bricks with their own hands made of gypsum are made using a drill with a nozzle in the form of a mixer. The resulting solution is poured into the mold. At the stage of maturation of the mixture it is important to exclude drafts and frost. Gypsum should not be mixed for too long, because the material quickly seizes. If you notice bubbles on the surface of the solution, then the mold should be placed on the vibrating table.

If you add cement to the gypsum composition, you will achieve an increase in the strength of the products. However, in this case, the finish will lose the property of antiseptic and can become covered with mold and fungus. Before you make a decorative brick yourself, you should familiarize yourself with certain rules. Among them, the time to freeze the gypsum, which is only 15 minutes, should be noted. If you do not have additional plasticizers that would guarantee the strength of the material, you can replace them with citric acid. After the brick is delivered and further processed.

Masonry made of plasterboard

Decorative bricks with their own hands from plasterboard are performed today by house masters quite often. To decorate the wall in this style, you should prepare:

• Wallpaper glue;
• Dry paint;
• Drywall;
• sand;
• Brush.

For starters, the sheet is drawn in the form of a masonry made of bricks. All the details in the next stage are accurately sawed with a jig saw. Each element is covered with a thin layer of wallpaper glue. Sand is poured into the surface through a sieve, the excess of which should be shaken. After the material must be allowed to dry out.

As soon as the sheet of drywall is dry, it can be started to be fastened to the wall. In order to achieve contrasting solutions, sand can be painted in different colors. This will make the room in a modern style. To ensure that the plasterboard is firmly attached to the wall, a mounting tape should be used . After completion of work using mechanical fasteners from the tape can get rid of.

Decorating walls for a brick with plaster

Decorative plaster for a brick with your own hands, you can also be applied. To do this, prepare some tools and materials:

• Acrylic primer;
• Roller;
• color;
• A bath for a paint;
• pencil;
• Wand;
• Gypsum plaster;
• brush;
• putty knife;
• level;
• Paint tape.

Technology of work: marking and priming of walls

Decorative bricks can not be made with their own hands before laying it. Sometimes for the decoration of walls in this style is used plaster. At the first stage, you need to perform markup. It will allow to draw up a small section of the wall. Using a level and a pencil, you need to draw a line on the wall that will indicate the transition. The outer contour is pasted with paint tape. The next step will be priming the walls. This will eliminate chips and cracks. Apply a primer with a foam rubber roller, and in hard-to-reach places and in the area of joints, you can work with a brush. This layer dries out about 4 hours.

Work with plaster

If you are thinking about the question of how to make decorative bricks with your own hands, then you can use one of the above methods. However, if there is no desire to apply the form, then plaster application can be used. Sometimes color is added to the solution to make the brickwork more realistic. It is not necessary to achieve absolute evenness, it is important to get the most natural surface.

Start work is necessary from the extreme areas, which are pasted with adhesive tape. The thickness of this layer should be a limit of 0.5 to 2 cm. For one approach, one should not try to impose plaster on a large area. If you are a beginner, you need to limit 0.5 m ² . Before the drying of the plaster, it is necessary to arm any objects like a thick knitting needle or wand. With this tool you need to press in the formed layer of the strip, which will simulate the gaps between the bricks. You can try to create a view from a chipped facade bricks. You can act with a narrow spatula. To give texture, the masters are advised to use a dry, hard brush, and it is necessary to act on the masonry, which has not yet dried completely.

Finishing

Decorative brick with their own hands can be created from plaster, which is applied to the wall. At the final stage, the masonry is rubbed with sandpaper. The wall can be painted with a roller in any shade. Use for this purpose is recommended paint on acrylic basis. After drying on the surface you should walk a semi-dry sponge soaked in a paint of a darker shade. Sometimes at this stage, use a semi-dry roller, which is dipped in the paint lighter. This will give the wall expressiveness.

Installation of decorative bricks: preparation of tools

The installation of decorative bricks with their own hands can be fully implemented. For this, there is no need to prepare complex rigging. To carry out the work you need to stock up:

• Construction roulette;
• With a pencil;
• With a hand saw;
• Level;
• Brushing;
• A metal ruler;
• Brush;
• Twine;
• Spatula.

If it is necessary to revet the walls of an impressive area, then a circular saw and skin will be needed to strip off the sawn pieces. The jointing can be done with different kinds of glue.

Preparation for work

To stick a brick it is necessary on firm and firm bases which should not sit down and be deformed. The surface of the wall and the back of the brick must be treated with a deep penetration primer. The horizontal surface needs to be marked out, which will perfectly connect the elements together.

If the finish is located in the corners, you need the appropriate elements, this will simplify the installation process. It is necessary to start work with them. In this case, the master will alternate short and long sides. If the installation is carried out without basting, the vertical seams should not be placed one above the other, they are usually displaced by about 5 cm.

Brick Laying

The adhesive solution must be applied to the surface with a spatula. The adhesive is also applied to the surface to be coated with a notched trowel. Hold the tool at an angle of 60 ° C to the surface. The decorative brick is gently pressed against the wall. It should be moved in different directions so that the clutch is better. Do not squeeze the solution, as this can subsequently prevent the next row from being laid.

False fireplace made of bricks

Decorative fireplace made of bricks is made by own hands only from several products. Usually it takes 25 bricks. Instead of overlapping, you can use a steel strip on which the mantelpiece fits. It can be made from a single 4-cm board. With such construction there is no need to make a foundation.

The brick is laid on cement mortar. In this case, additional finishing is required. Experts recommend taking the following dimensions as the basis: 0,9 x 0,25 m. In this case we are talking about the parameters of the base. With regard to the furnace opening, it can have the following dimensions: 0.5 x 0.38 m. The walls in this case can be laid in half a brick.