Canopy of corrugated board: installation technology, features, schemes and recommendations

If you are going to do the construction of the house territory, then you should choose the type of construction. This is especially true when it comes to a canopy. Not always there is an opportunity and desire to build a separate edition. Sometimes it is enough to install a canopy to ensure its practical use. With its help it will be possible to arrange a place for a cozy rest, to store household items. The most important step is to choose the material. The optimal solution will be a corrugated board, which is distinguished by its durability and strength.

dimensions

It is made of galvanized steel. Its thickness varies from 0.5 to 1 mm. During the manufacturing process, the material is coated with a protective layer of polymers. The standard sizes of the canvas are as follows: width - from 80 cm to 1.1 m; Length - from 2 to 6 m, height - from 8 to 130 mm. The last parameter is the distance that connects two corrugations. The more it is, the more spacious the product looks. If you decide to make a canopy of corrugated board, then it is better to choose a galvanized version of the material than polycarbonate. It has higher rigidity. It differs in resistance to the load, which arises from the pressure of the thickness of the snow. This fact serves as an important condition for the design of such a design.

For reference

When a hinged single-deck structure is assembled, it is important to ensure the correct tilt angle. Otherwise, the precipitated precipitates will be delayed, overloading the light frame.

Shedding device

On sale today you can find ready-made sets of canopies. The consumer will only need to assemble the structure using the proposed drawings. In any case, the canopy will consist of a frame and a covering. For the first element you can use wooden beams of hardwood. They are treated with special solutions. As an alternative solution are the steel profiles.

The support will be subjected to a vertical load. Therefore, for its manufacture, metal profiles of 6 x 4 cm can be used. If the structure seems more dimensional, then for reliability it is necessary to apply a section of 8 x 8 or 10 x 10 cm. The number of supports can be easily determined by calculating the gap between them equal to 1 m. At the same time, the construction resting on the wall is not taken into account. Producing a canopy of corrugated board, you will need to purchase material of the brand HC44 or HC35, which will withstand heavy loads and provide a drain.

Calculating the canopy

Calculate the parameters of the canopy for the car can be, referring to the dimensions of the machine and the parameters of the protective structure. Thus, if the vehicle has dimensions of 1.6 x 4.3 m, then the site size should be 2.3 x 5.5 m. If it is an off-road vehicle, the parking lot is increased: 3.5 and 6.6 Meters. As the optimum height of the canopy is the one under which can fit the car with a raised trunk. However, if you make more than 2.3 m, then the canopy will be exposed to rain and snow.

Preparation of tools

In order to make a canopy from the corrugated board, it is necessary to prepare tools: a building level, a tape measure, a hacksaw, a screwdriver, a welding machine, galvanized screws, a hammer, a screwdriver, a drill, a set of wrenches, bolts and fixing angles.

The technology of mounting the adjacent canopy

Regardless of what kind of design you choose, it will be considered a prefabricated structure. You can do such work yourself without resorting to outside help. To produce a single-deck construction that adjoins the house, it will be necessary to prepare and calculate the territory for construction. At the next stage the playground is leveled. After that, the soil is compacted, and pit pits are excavated along the perimeter. Place the indentations in two rows, each with 3 elements. Schematic you should get a rectangle.

When the canopy is made of corrugated board, the next step will be to install the racks. They should go below the freezing line of the ground. Cement mortar is poured into the hollow space, after which it should be completely dry. With the help of fixing corners and screws, transverse beams are attached to the posts. The angle of inclination should be adjusted due to the difference in length of the opposite supports.

The frame is covered with a primer. It is necessary to wait for it to dry out, and then apply a coat of paint. Next, sheets of material are stacked, while overlapping in one wave should be observed. The sheets are fixed with self-tapping screws to the transverse beams. A square meter will require about 7 galvanized self-tapping screws and rubber gasket, which will exclude damage to the protective coating.

Recommendations for the manufacture of an alternative version of the canopy adjacent to the wall

One-pitched canopies made of corrugated board, which are adjacent to the wall, can be manufactured according to a simplified scheme. In this case, you will need to ensure the presence of several basic elements, among them:

• support;
• Outer columns;
• Vertical racks;
• Crate;
• Framework;
• Drainage.

The cant will make a support. It connects to the supporting wall with the help of anchors. Support is the main element. Therefore, it assumes a reliable fastening. The outer columns are vertical supports, for which the total load will be distributed. They can be made from a profile or asbestos-cement pipe. Sometimes a bar of square cross-section is used. For each such rack it will be necessary to build a foundation in the form of a concrete foundation. In all cases, it is important to remember that it should not lie above the depth of freezing of the soil. Otherwise, the deformation of the frame can not be avoided in any way.

When the canopy for the car is made of corrugated board, the outer vertical posts or pipes are laid with a Mauerlat. It is a cross bar. He acts as a support for the rafters. Cross the lath of the canopy. It is made of boards or thin rails. On top is the corrugated board. Its connection with the frame is made by screws or bolts. The drainage from the plastic pipe is installed if necessary. If the lower edges of the structure go above the ground or lawn and do not cause inconvenience, drainage is an obligatory part.

Features of the construction of a separate canopy

Canopy made of corrugated boarding in the yard can stand separately. To do this, you need to build a foundation and build a crate. After the marking of the territory, support pillars are installed, the distance between which should be 30 cm. They are digged 30 cm deep into the depth of the pit. However, with an increase in the height of the pillars, it is necessary to drive them deeper into the ground. As in the above-described case, each support is poured with a solution. To install the frame, you need metal pipes. In the process of drying the foundation, you can do the welding of the crate. The first to install lags, which will perform the supporting role of the frame. They are welded to reinforcing bars, treated with an anti-corrosion agent, if necessary, weld seams are painted. After making the frame, you can start installing sheets of corrugated board.

The material that has a polymer coating, easier to install, has a longer life. In addition, it is more resistant to vibration and precipitation. When awnings made of corrugated board are made in the courtyard of a private house using such technology, the sheets should be installed with the help of fasteners with rubber gaskets. The lapping in this case can make a limit from 4 to 6 cm. If it is a question of one-pit designs, then it can be equal to 4 cm. Parking car roofs are usually strengthened by stiffening ribs. This is especially true in the case when using a wall covering instead of a universal one.

Cost

Canopies made from corrugated board, the price of which is calculated by the materials used and the size of the structure, can cost the consumer 1500 rubles. Per square meter. When ordering such a facility, specialists can not limit themselves in the forms of overlapping. The structure can be arched, one- or two-spaced, adjacent to the wall or separately standing. If you want the canopy from the corrugated board to last longer, then it's best to abandon the wooden frame, replacing it with metal. But even this material is corroded if it is not properly maintained. Therefore, it should be asked how the company's experts produce the preparation of poles and poles, as well as the constituent elements of the roof.

If you yourself want to make such a design, then you can choose pipes as supports, whose diameter should be 8 cm. Do not use those whose length exceeds 3 m. It is important to choose the right product, depending on the thickness of the walls of the pipe. The greater the anticipated load on the canopy, the greater this parameter should be. Make a canopy of corrugated board can be with the deaf side walls. This will allow using the design not only for the car, but also for summer gatherings during the rain.