Wooden stand with own hands

If you have a warmed loggia, a free space has formed in the winter garden or in the kitchen, then you can think about how to make a bar yourself.

Can I replace the desk table

Some masters, looking at the inhabitants of America, try to apply this piece of furniture as a dining table. The wooden stand can only become an addition to the dining area, as in our country there are very different traditions. Behind the counter can not fit all family members. But if you make this design and install it in the dining room, it will be quite convenient to use for snacks and gatherings with friends.

Features of the bar

The wooden stand must have certain parameters, so its height can vary from 110 to 115 centimeters. This indicates that the bar stools need to be made or purchased, taking into account that they correspond to a new piece of furniture. Chairs should be high enough, in addition, they must have footstools. For the reason that the wooden stand will have a rather impressive height, this feature can be used. Under the surface of the lid, you can place an additional compartment for storing alcoholic beverages, fruits, vegetables, and utensils. Do not forget about the top rack module, this part can also be made functional, in this area you can install an element on which it will be possible to hang glasses and wine glasses.

Additions to the construction

The design can be supplemented by some components, among them one can distinguish the built-in key, designed for uncorking bottles. This may be a bucket that you will fill with ice, among other things, you can design drawers. If a wooden stand is to be installed in a small kitchen, then this piece of furniture should not be made too high, since it will look inappropriate, and will also clutter free space. In this case, it is preferable to construct the device in the form of a folding structure, which will act as a continuation of the dining table. In this case, the wooden pillars of the supports can be made retractable.

Preparatory work

The wooden stand of independent manufacture will differ from expensive designs, but it can be approached to such device which are supplied with the chromeplated elements. During the work will have to use chipboard, as well as sewer pipes.

Preparation of materials

In order to produce the work, you need to prepare 6 sheets of particle board, the dimensions of each of which should be equal to 16x440x1150 mm. It will take a sheet of chipboard in the amount of 2 pieces with other dimensions, namely 16x1000x2000 mm.

It will be necessary and rake with the dimensions of 20x40x4000 mm.

The master will have to prepare a sewer pipe made of PVC with a diameter of 180 millimeters, whereas the length of this element should be equal to 950 millimeters. This workpiece will form the basis of the legs of the rack. In order to make the body of the lamp, you will need to prepare the same tube, but cut it in such a way that the length was equal to 450 millimeters. It will take a steel pipe with a diameter of 50 millimeters, its length should be equal to 1 meter, this element will form the basis of a horizontal leg support. A wooden bar counter will be assembled using dowels 5x50 mm, 80 pieces will be needed. Prepare a luminaire of the appropriate style, as well as wires for it. The design after manufacturing can be treated with a colored varnish designed for working with PVC. Useful in work and acrylic paint, as well as putty. Additional fasteners will be screws that have a countersunk head, their dimensions should be equal to 4x60 millimeters, and also 4x80 millimeters. You need to stock up and dowels.

Preparation of tools

Installation of wooden racks should be done with a drill, drill, jigsaw, clamps, round file, spatula, paintbrush, hacksaw, grinding bar, as well as a screwdriver. Due to the fact that the bar counter should have a high degree of reliability, the parts should be the most durable, this indicates the need for the initial bonding of each other with particleboard, in the end you should get plates with a final thickness of 32 millimeters. It should be noted that two canvases, the dimensions of which are 16x440x1150 mm, should remain unscoupled.

Cutting of chipboard

If you need a wooden bar, you need to prepare some elements from the chipboard, among them you can select a circle with a diameter of 175 millimeters. In this blank in the central part, you need to prepare a hole through which the wiring will be stretched. It will be necessary to cut out of the same material an outdoor circle, whose diameter is 500 millimeters. It will take a bearing pad, which is a circle with a diameter of 300 millimeters. Above it will be located a ceiling hood, which is represented by a ring, its outer diameter should be equal to 300 millimeters. The inner diameter of this workpiece should be equivalent to 180 millimeters. It is necessary to prepare and the frame intended for the bottom pipe, it will be two identical rings, the outer diameter of each of which is 240 millimeters, as to the inner diameter, it should be equal to 180 millimeters. If you need a wooden stand, you can make it yourself, so you will need a wall that will be located between the table top and the shelf, this workpiece is a strip, the length of which is 870 millimeters, while the width is 240 millimeters. Prepare both the lower and upper shelf. On the one hand, two plates, the dimensions of which are 32x440x1150 mm, should be made rounded. After you retreat from the edges of 190 millimeters, and from the lateral edges 130 millimeters, you can make a hole, whose diameter is 180 millimeters, it is useful for installing a vertical support tube.

Features of the table top

Using one of the plates, whose thickness is 16 millimeters, you need to make the same cutout, as described above. This will become a technological hole that should not be through, it must be installed in a vertical support. At the next stage, you need to fix the workpiece and the slab with a thickness of 16 millimeters with the help of glue. After you can cut out the countertop. Once the elements are glued, they must be strengthened with clamps, until the blanks are completely dry, only after you can go on to sawing.

Implementing the rack assembly

Wooden stands for flowers can be manufactured using the same technology, moreover, such pieces of furniture can be used for different purposes. Producing this design, the ends of blanks need to be cleaned, then covered with putty, and then sanded. Before starting the assembly, all the elements that have a roundness, this applies to the plastic pipes, it is necessary to paint or varnish in two approaches. Between the layers it is necessary to withstand the time interval, which will be necessary for the complete drying of the composition. The assembly of structures should begin with the fact that between the lower shelf and the tabletop you need to install a vertical wall, the dimensions of which are equal to 240 x 870 millimeters. To do this, use dowels with a diameter of 5 millimeters. This element must pass in the central part of the countertop. Now you can take a pipe, whose diameter is 6 mm, and the length is 450 mm, in order to make several through holes in it. Use a pipe that is intended for the lamp housing. Performing these manipulations, you need to retreat from the edge of the workpiece 20 millimeters, while the diameter of the holes should be equal to 3 millimeters.

Now you can assemble all the elements of the rack into a single unit for this, the supporting slats need to be fastened to the ends of the shelf. The next step is to fix the wooden stand. After that, you can install the upper and lower shelves. Now it remains only to paint everything. From dyeing, the wood will look even more attractive, in addition, it will protect its texture, prolonging the life span for many years. The design will please you, and you will enjoy the work done.