Installation of Rehau pipes with improvised means

The company Rehau, which is located in Germany, has been manufacturing pipes and fittings since 1948. This product is known and recognized all over the world. In the production process, cross-linked polyethylene is used, which ensures reliability and a long service life of the products. Specialists note that it is not only professionals who are able to install such pipes, but also home masters who previously had no experience in carrying out these works.

Why choose pipes "Rehau"

Such pipes are produced with the use of new technologies, this explains their principal features, which consist in:

• Increased noise insulation;
• The ability to mount a unique method;
• Universality of the material;
• Crack resistance;
• Deformation stability;
• High degree of isolation;
• The ability to undergo temperature changes;
• Safety for human health;
• Special internal coating of the walls.

For the reason that the installation of such pipes is carried out using a unique technology, you will be able to create the most durable connection. Among other things, both cold and hot water can be supplied through these pipes. The maximum temperature of the liquid can reach 95 ° C.

Pipes are almost not subjected to mechanical damage, so they can be stacked even under the plaster or by another closed method. The material has a high degree of thermal insulation, which saves resources. Among other things, pipes are able to undergo temperature changes and high internal pressure.

Preparing for pipe installation

The installation of Rehau pipes should be carried out after the completion of the preparatory phase. For this, a tool and pipes are purchased. You will need fittings and adapters, and when calculating the required materials, it is best to use a pre-compiled scheme. For the installation work, you will need an expander with a set of nozzles for pipes of different diameters. The tool is better known as an expander. It is necessary to prepare a press clamp with nozzles of different diameters, since the installation is slightly different from conventional welding. For the procedures, you will need a tool from the same manufacturer. In any case, it will not be without a pipe cutter, but it certainly exists in the arsenal of the home master. Prepare a marker for marking pipes and tape measure.

The installation of Rehau pipes can be carried out independently, as the above-mentioned tools are usually available for every home master. And if not, then the repair kit can be purchased for only 2500 rubles, which will justify the refusal of professional assistance.

Pipeline assembly

The installation of Rehau pipes without special tools should begin with the preparation of the products, while the workpieces of suitable dimensions should be cut. Fittings are being prepared which will be useful for assembling different sections of the pipeline. If the installation is carried out using pipes "Rehau", then all parts of the system should be prepared and verified that the segments were cut according to the scheme. To check the fittings and pipes it is recommended to spread out on the floor in the required sequence. This is especially true for the arrangement of heating of city apartments, since it will be necessary to turn off the system throughout the house.

When cutting pipes it is necessary to follow the well-known Russian proverb. The installation of Rehau pipes with improvised means is possible, but it should only be carried out using properly prepared lengths. If you make the mistake, you can not install the pipeline system without purchasing additional pipes. Docking of fittings and products among themselves is carried out by sleeves, which are installed by a certain technology. The expander should be matched with a nozzle with a diameter that corresponds to the parameter of the pipe used. The handle of the tool should be diluted, and its ends are located at right angles to each other. The nozzle on the expander must be fixed firmly and held on the pin, during installation it is necessary to feel the emphasis. On the piece, which is supposed to be connected to the fitting, the sleeve should be put on. Its diameter should match the diameter of the pipe.

Methods of work

When installing Rehau pipes, you should pay attention to the fact that the casings have chamfers, and when installed they are directed towards the joint. The next step is to put a pipe on the other end of the nozzle. When the handle is reduced, the tube expands. The expansion end is connected to the fitting, which is installed in this place. A sleeve is brought to this element, and after that, using a press clamp, it should be moved to the fitting. On this we can assume that a reliable and lasting connection has been obtained.

For reference

When installing Rehau pipes, small inconsistencies should not be allowed. The joining elements must be placed horizontally to each other. If you ignore this rule, then the connection is not very reliable.

Guide to the use of a press tool

If the press tool is used in your work, then in the first stage with it you need to grab the connection and switch the lever to the upper position. This will compress the elements. Handles of the expander must be moved, and then put the sleeve to the flange. The next step is to bring the tool lever back to its original position, with the lever at the bottom of the side.

When a press tool is used to mount Rehau pipes, the next step is to move the handles together. The movable handle must be raised 90 ° sharply to bring the tool to its original position.

Cost of installation

The installation of "Rehau" pipes, the instruction for which is discussed in the article, can be conducted by professionals. If you decide to do this work yourself, then they will not cost more than installing pipes made of metal-plastic or cross-linked polyethylene. This is due to the wide spread of technology or its leading positions in the market.

When there are no tools at hand, you can use the help of specialists. They set the points of intake of hot and cold water without slabbing and take for such work from 1500 rubles. When the pipes are laid in the corrugation, the cost of works will be equal to 80 rubles. For running meter. If in an apartment or house there are already pipes of the brand "Rehau", and to them there is a need to remove the towel warmer, then you should count on the amount of 3000 rubles.

Conclusion

Installation of Rehau pipes, photos of which are presented in the article, may provide for a whole range of works in the bathroom. In this case, quite often the elements of pipes are output to the kitchen. If the master will not use the method of slaughtering, then the work will cost 10,000 rubles. or higher.