How to make a tool box with your own hands?

In order not to waste time searching for tools (hammer, screwdriver, wire cutter), you should store them in one place. But what should I do if all the racks and cabinets in the house are full? An excellent solution to this problem will be a self-made tool box. You do not need special knowledge and skills. The process of manufacturing a portable box will take no more than 3-4 hours.

Where do I start?

The first thing you need to decide is the size of the box. Here everything depends on the size, quantity and total weight of the tools that will be stored in it. As for the configuration, it does not really matter. The finished product can have a square, rectangular and any other shape. As you wish.

A homemade tool box is usually made of sawn timber or artificial wood (OSB-plate, plywood sheet, chipboard). Often used different metals and high-strength plastic. It is difficult for beginners to work with these materials. Therefore, they prefer a tree.

How to make a tool box : expert advice

If you do not want to make gross mistakes and waste time, then listen to the recommendations below. Only in this case you can count on a good result.

1. To make a convenient and reliable tool box with your own hands, you must first draw a design drawing. This is done taking into account the type, number and total weight of the instruments.

2. Usually boxes are made of boards, used earlier in other designs. Before reuse, they are cleaned of dirt and dust. For lightweight tools, it's better to take plywood, and for heavy tools - hardboards.

3. On the wooden surfaces, markings of all the details of the box are marked. Next, we cut the workpieces using a jigsaw or a saw with small teeth.

4. Do you want to make an open tool box yourself? This design provides a central handle. To install it, you need to drill 2 blind holes.

5. Assembly of parts is carried out with the help of screws and screws. Secure the handle securely and glue all the seams.

6. To make a tool box with your own hands - only half of the matter. You still need to give it an attractive look. You can cover the surface of the drawer with paint or a special varnish.

Tools and materials

Very soon we will begin the practical part, but for now we will prepare everything necessary. So, for work we need:

• drill;
• PVA glue;
• Plywood (thickness 12 mm);
• Saw blade for jigsaw for wood;
• a hammer;
• Jigsaw with a sawing function at an angle of 45 degrees;
• Varnish for wooden surfaces;
• drill;
• Several bars 15x15 mm;
• Clamps;
• Small nails.

We make a tool box by our own hands : a step-by-step instruction

What should we end up with? Wooden construction, where in the future will be stored nippers, screwdrivers, hammer and other tools. The action plan is as follows:

Step number 1. First we take plywood in hands. We will use it to make the side walls of the box. To the ends are well docked with each other, they need a little pruning, placing the saw blade at an angle of 45 degrees. A similar kind of docking is called a connection by a specialist.

Step № 2. We smear the ends with joiner's glue. If you have not managed to buy it anywhere, then use PVA.

Step 3. We proceed to assemble the entire structure. That the details do not crumble, they need to be fixed with adhesive tape. Make sure that the walls are connected evenly. Now we wait until our workpiece dries.

Step number 4. To the existing design, we nail the slats that will hold the bottom of the drawer. Here you need to be careful, because the nails are very small.

Step number 5. Make the bottom of the box, and then glue it to the rails. We use the same PVA.

Step number 6. For convenience of carrying the box we make a handle. We take a thin board. The electric jigsaw cut out the thinning on it. It is very important. Also, do not forget to cut out small rectangles from each corner of the handle. Their depth is equal to the thickness of the plywood, from which the sidewalls are made.

Step 7. In the side walls we drill out and cut out the notches under the handle. Make sure nothing is loose. In the side of the handle and the walls of the box there must be blind holes for inserting the dowels.

Step number 8. Let's move on to assembling the handle. All its joints to the sidewalls, as well as the sidewalls with the walls, we diluted the PVA well. Gradually we collect the handle parts. We fix its position with clamps.

Step # 9. All that remained for us to make is a holder for the compass, a chisel and a screwdriver. We will use plywood. We cut out of it a strip, the width of which is 4-5 cm, and the length is equal to the inner dimension of the long wall of the box. Then drill holes for tools. The band is coated with glue and attached to one of the walls using clamps. Once the glue is completely dry, you can start finishing the surface of the box. For this purpose, a varnish or paint is suitable.

Conclusion

Now you know how to make a toolbox yourself. There is nothing complicated. The main thing is to strictly follow the instructions described above. Materials from which the design is created can easily be purchased at any construction shop.