Built-in electric hob. How to build in the hob

In our time, more and more often give preference to hobs, and stationary slabs are gradually disappearing into the past. And it's not just that, such devices save space and serve as a good assistant in cooking even the most complex food. Unlike standard plates, it is possible to build the hob in any place, most importantly, for it to be cut out a special opening in the countertop.

Basic Types

To date, there are two types of devices. For those who like the independent built-in electric hob, it will be easy to install it in any chosen place, it is completely autonomous. For dependent surfaces, the same oven is also sold in the kit, they are mounted only under each other. The control buttons of these devices are very often located on the same panel. This combination does not suit everyone, so that the independent surfaces are more popular.

Installation instructions for the panel in the countertop

In order for the built-in Bosch hob, for example, to be installed correctly, follow the specific instructions:

1. Initially, the manual is studied from the box, it is necessary to find information about the estimated size of the niche, which will need to be cut. In the event that it will be absent, you will have to independently measure the interior of the seat. Take into account that the ideal gap between the table top and the panel will be 1-2 mm, if it is larger, there is a possibility that during the operation the built-in electric hob will "walk".
2. Next, we mark the countertop. Be sure to draw the lines along which the electric jigsaw must move , this will require a pencil and a double ruler. Very often a cardboard template is included with the device, which makes it easier to measure the required area. After marking at the corners, you need to drill small holes with a thin drill, so that the blade can enter when cutting.
3. Then select a fine-toothed file for the jig saw on the tree, and very carefully, along the line of the pencil, cut out the hole.
4. In order to protect the joint from dirt and moisture, as well as to prevent the appearance of fungus, a sealant is usually pasted around the perimeter, which is usually included in the kit, but if it is not, then acrylic or silicone sealant is perfect. All protruding excess is removed with a knife.
5. Next, carefully begin to install the hob in the niche that was cut out. If it came out a little more than the required size, then it will need to be leveled on the countertop. In the event that it is not possible to install the device, you do not need to cram it with force, it's better to gently cut a few millimeters.
6. At the end, the installed panel is fixed with special clips from the kit, they need to be screwed.

Surface material

Before you buy a hob, you need to determine the material from which it should be made, as often they are made of enamel and stainless steel, and also of glass ceramics. On each kind of surfaces there are positive, and in some cases also negative user reviews. Built-in ceramic glass hob attracts its appearance. It is widely represented in the domestic market. Such devices quickly gain the right temperature and also cool down, their segment is considered the most expensive.

Enamelled panels are strong enough and painted in a wide variety of colors, which can very nicely fit into the design of the kitchen. The main disadvantage is the complexity of care and cleaning.

Stainless steel looks expensive and stylish, has high strength, but at the same time quickly gets dirty from fingerprints.

Electrical connection

It is not enough just to properly integrate the hob, it must also be connected, for this, follow the instructions:

• Check if the actual voltage in the network matches the one specified in the documents;
• Factory settings can be found on the bottom of the panel;
• In order to reach the terminals, it is necessary to open the terminal block ;
• When connecting to the mains, be sure to provide disconnect devices that disconnect all the contacts - for this, protective current switches and fuses are perfect, all connections must be made taking into account their load and capabilities;
• Built-in electric hob (Bosch, for example) can be mounted between furniture elements, the main thing is that it is under the hood;
• After the work has been completed, check that all conductive elements are well protected from contact with people and animals;
• Make sure that the connecting cable is not clamped or pinned to the point during installation;
• Do not touch the heated hotplates.

Installation of the gas surface

When connecting such devices, be sure to check that there is good ventilation, for this you need to do the following:

• Work should be started after receiving the instruction and familiarization with the conditions of the gas supplying enterprise;
• On the underside of the device there is a gas pipe with an external thread;
• A non-metallic gasket and a device for liquefied gas are necessarily included;
• When installing, clamp the tube so that it does not rotate;
• For a sound seal, approved non-metallic components and other materials must be used;
• Permissible deformation of gasket compression is 25%; The device must be connected using a certified flexible hose, which must pass freely and not touch the kitchen implements.

Cover for surfaces

After it has been possible to build in the hob, it is possible to mount a cover to it to additionally protect it from mechanical damage, it is mounted separately. In the closed position, the surface can be used as a table top, which increases the working area. For its production, glass ceramics, glass and enamelled steel are most often used. The cheapest option is a metal cover, which is second only to its simplicity to everyone else. Pottery and glass are easy to use, they are beautifully washed and well-looked, so their cost is slightly above average.

Surface Accessories

For hobs are also invented and additions that simplify its use.

1. Very often lattices are used, which serve as a support for dishes. Such adaptations can be integral, and also consist of several halves. The use of the second option is more convenient, since the pollution created during cooking is easily eliminated. These components are often used by Bosch. The cooking panel built-in can have different versions of grate materials, such as cast iron or steel.
2. Burners - this is an obligatory attribute, which is always supplied with the hob gas built-in. Comments on the required number and their accommodation options can give any hostess, who often uses them. Many argue that the cooking parameters depend on the distribution of the burners, there may be up to 6 pieces on the panel, they must necessarily be different in size and, accordingly, in power.

Hob control

All surfaces can have mechanical, electronic and electromechanical control.

The mechanics are installed in the most budgetary versions with minimal functionality.

The use of electronics will greatly expand the list of cooking functions, namely:

• Maintaining a uniform temperature;
• Timer, it can be switched on at the right time;
• Various modes of heating;
• Control of cooking, after the dish is ready, the panel will notify about it;
• Recognition of dishes or material, the hotplate will begin to heat up only when the object is on it;
• Boiling - after boiling, the heat supply goes into a less active mode;
• Recording in memory - once prepared the right dish, you can bring the technology into the memory of the device and the next time to reduce the degree of its participation to a minimum.

Safety when using panels

Modern built-in hobs of 45 cm or more must be properly installed and connected, preferably under the supervision of specialists, then they can not do any harm to a person. In order to prevent possible accidents, the mounted models are equipped with such devices:

1. Surfaces operating on gas are equipped with a system that controls its supply and combustion. If the flame goes out, the burner switches off automatically.
2. The electrical panels have a three-pole plug, in which the ground is located.
3. If the surface itself fails, it begins to emit sound and light, and then completely turns off.
4. "Child protection" will help prevent accidental activation of the burners.
5. Light indicators will show the user that a high temperature has already been reached.

Price

For those who want to build a hob, an important factor is the cost of such a product, it varies widely enough. Budget models cost from 3,000 to 15,000 rubles, the average range is from 16,000 to 50,000 rubles, and a great price can be paid for luxury options. Basically it depends on such indicators:

• New on the market. The maximum cost will have a model that appeared relatively recently.
• Exclusive. The surface, which has a unique design, will cost several times higher than mass production.
• Brand. The goods of well-known firms are much more expensive than their less well-known analogs, although the quality of the second ones can be much better or the same.