Makita LS1040: user manual, reviews

Saw Makita LS1040 is a crosscut device that can be used for sawing wood, soft metals, plastic and laminate. This tool has a fairly small size, but it differs in power, which allows you to cope with the tasks. Experts do not advise buying such a device for solving household problems, since the price of equipment is quite impressive, and it is intended for professionals. Not always such devices are convenient for the average user, since they have an impressive weight and high power. The last circumstance says that you overpay for the unit, as you will rarely use it. Best if you need to cut metal, wood or plastic, contact a specialist. Carrying out such works will cost inexpensively, but if you buy a similar tool to solve your own needs, then it most likely will not meet your expectations.

Feedback on the main characteristics

The saw Makita LS1040 works at the expense of the engine on 1650 W, and kroit with the use of a large saw blade. The master will be able to apply in the workpiece, the maximum width of which is 95 millimeters. As users emphasize, using the functionality of fixing the shaft, you can change the snap. The seed diameter of the disc is 30 millimeters, while the diameter of the cutting element is equivalent to 260 millimeters. The maximum depth of the cut is 67 millimeters, which is true for an angle of 45 degrees. This parameter is increased to 95 millimeters if the angle is equal to 90 degrees.

Along with the positive characteristics, consumers identify and negative, among which such as the lack of lighting and speed control. Afflicted by experienced users and the fact that there is no possibility of horizontal displacement. Model Makita LS1040 has a rather impressive weight, which is 11 kg, but this is normal for such a variety of equipment. The device is powered by a brush motor. By purchasing a similar unit, you should pay attention to the fact that you will not be able to adjust the depth of the cut, as well as use a laser. All the shortcomings are successfully compensated by positive features, for example, with an impressive enough cable length, this parameter is 2.5 meters.

Feedback on additional features

The Makita LS1040 saw is a rigid construction that can be used for neat cutting of different materials. Consumers like that they can use the oblique cut to the left, exposing the angle from 0 to 45 degrees. The presence of a swivel ruler provides quite convenient support for the rod. This tool is chosen by professionals, as well, it copes with such tasks perfectly. If you use special saw blades, as the buyers claim, then you can use the equipment even for cutting aluminum profiles.

Usage feedback

The saw Makita LS1040 is assembled on a solid horizontal frame, on which a turntable is fixed. The latter allows you to specify the angle of cutting. In the far side of the turntable, a swivel arm is fixed, which is a pendulum. On it is an electric circular saw. Experienced masters advise to feed the workpiece along the guide, and the angle of cut in relation to it can be selected by turning the circle. In order to correct the angle, it will be necessary to loosen the handle. Consumers advise turning it counter-clockwise. As soon as the handle is in position, when the arrow points to the desired angle, it is necessary to fix this element by turning it counter-clockwise.

Safety instructions for use

Makita LS1040, the operating instructions of which must be read by you before using the instrument, is operated in conjunction with the goggles. It is important to properly prepare the place of work. This implies that it is forbidden to use the saw next to flammable gases or liquids. Before work it is necessary to check the disk, whether it has any damage or cracks. If any have been found, then the element must be replaced. Experts recommend using only those flanges that are designed for a particular model. It is important to avoid damage to the shaft, flanges or bolts. If this happens, the disc will go bad.

The master should make sure that the turntable is locked correctly, it must never be moved during operation. Before the saw miter saw Makita LS1040 is started, it is necessary to remove chips from the table, as well as small elements. The operator should avoid cutting the material in nails. Before starting the manipulations, you need to check and make sure that there are no fasteners in the workpiece.

Mounting instructions for saw blade

Before installing or removing a disc, it is important to make sure that the tool is turned off and the plug must be unplugged. Use the socket wrench when removing the disc. The central cover must be held in place, and after doing the turns counterclockwise. It is necessary to press the latch so that the disc does not rotate. Next, using the miter key, you clockwise loosen the hex bolt, flange and disc, then install a new disk. The direction of the arrow on the surface of the disc must coincide with the arrow on the casing.

Recommendations for using the dust bag

If you purchased the mitered Makita LS1040, it is important to know how to use each part of the tool. This also applies to the dust bag, which should be used for accurate work and easy collection of garbage. To connect the bag you need to insert a nozzle into the dust extraction holes, and after fixing the mounting holes of the element around it. Once the bag is half full, it should be disconnected from the tool, and also open the buckle. The bag is released from the contents, shaken, which will release it from the particles, as well as from the material that has gotten inside.

Adjusting the saw angle

Before starting maintenance or repair work, it is necessary to make sure that the equipment is disconnected and the plug is disconnected from the outlet. Quite often there is a need to adjust the saw angle. The machine is regulated at the factory, however, an additional adjustment may be required during operation, which should be carried out in several stages. To begin with, the clip is loosened, which fixes the turntable. It must be rotated in such a way that the pointer is at 0 degrees of the scale of oblique angles. The clamp should be tightened, and then loosen the bolts with the hexagon head on the stop. A straight angle is established between the plane of the disc and the guide stop, while using a right-angled triangle.

Instructions for cutting patterns by pattern

Makita LS1040, the reviews of which were presented above, can be used for cutting parts by template. In order to increase the efficiency of work, it is necessary to use dial plates, which are delivered separately. The master marks the pattern cutting line on both sides of the groove on the plate with a long hole. Further, by holding the sample, you must move the dial plate along the edge of the specimen. The plate is fixed with a screw. If you do not use it, you should loosen the screw and push it away from the place.

Conclusion

Quite often consumers are interested in where to buy original spare parts for Makita LS1040. If any element fails, it is best to contact a service workshop where they can select the component of the structure and install it in place. As practice shows, spare parts for the saw model are quite accessible, they can be purchased almost everywhere. It is important only to exclude the purchase of a fake, which is why the seller is recommended to require quality certificates for products.