M300 dry mix: types, technical characteristics, application features

In the construction market, there are more and more new materials designed to facilitate and accelerate the construction process, improve its quality. One of such materials is dry mix - sand concrete.

Features

This recently appeared construction mixture immediately began to enjoy increased demand, because it is a universal material with excellent characteristics. It consists of cement and a number of additives, so that the prepared solution quickly solidifies. If we compare the material with analogs, sandblast M 300 is significantly ahead of them in a number of indicators. These are:

1. High reliability and durability.
2. Maintain their properties for a long time.
3. Ability to carry the highest loads.
4. Stability against damage of any kind, including mechanical ones.
5. High density.
6. Resistance to moisture, adaptation to rapid changes in temperature conditions.
7. Available for any consumer cost.
8. No shrinkage.
9. Water resistant.
10. Ecological compatibility.

Scope of application

Peskobeton M300 is a dry mix. It is especially practical, versatile. Can be used in all construction areas when working inside and outside the facilities. The material is indispensable when it comes to the strength of concrete structures and structures. Building complexes, residential buildings, buildings for household and household purposes - this material is used everywhere for the preparation of solutions. It is used:

1. When installing.
2. When pouring the foundation under the structure.
3. When making floor screeds.
4. When leveling surfaces.
5. For sealing cracks.

Due to its resistance to external factors and rapidity of hardening, the M 300 sand concrete is used for work at emergency facilities where these properties are very important.

Restoration of surfaces of different kinds, laying of stairs, paths for the garden, the manufacture of different types of paving slabs, curbs - these and many other types of work are also performed today using sand-concrete solutions. In addition, the M300 sand concrete is used: the dry mix is the main component for the preparation of expanded clay concrete.

Method of use

But, in order for the result to be qualitative, the surface must be carefully prepared before applying the solution. To do this, remove dust, paint, dirt, loose areas, which can later be crumbled. If there are large cracks, they must be repaired. Before applying the solution, the surface must be primed or moistened.

If vertical surfaces are treated, the work is done as follows:

1. Beacons are installed. They are needed so that it is possible to level the solution to obtain a strictly horizontal surface.
2. After that, the M300 sand concrete is used. The dry mix is mixed with the liquid at the rate of 1: 5.
3. With the help of a mixer, the solution is mixed until a plastic, homogeneous mass is obtained.
4. The required amount of solution is poured onto the prepared surface. It should be so much that it was convenient to work.
5. The solution is leveled out using the rule.

To keep the solution after drying has retained its properties, it is necessary to observe the following measures: periodically moisturize the surface, protect from drafts and ensure that at least 72 hours the sun's rays do not reach the drying solution. After a week, the surface will be ready for further work.

Composition

How is sandblasted M300 manufactured? Dry mixture is a material that is a consequence of the use of familiar materials and the introduction of new developments and technologies. Particular attention in the manufacture of the material is paid to the observance of the proportions of the components, otherwise the expected effect is unlikely to be achieved: all the characteristics of the material will change, and such important as water resistance, frost resistance.

The main component of the mixture is one of the new types of cement - Portland cement. It consists of gypsum, to which is added crushed clinker and sand. Improve the quality of the material special additives - granite crumb, plasticizers, etc.

Types of mixtures

Depending on the components used, the mixture of M300 sand concrete is divided into the following types of properties:

1. Coarse-grained mixture. It is characterized by a long service life and the highest strength characteristics. It is designed for pouring foundation structures.
2. Medium-grained mixture. Screeds, paving slabs, self-leveling floors - these and many other works are performed using medium-fractional mixtures.
3. Fine-grained mixture. Has increased reliability. It is used as an external plaster, used as a grout remover.

To produce a specific type of mixture used special grids, special equipment, vibrating plants, various tools.