How do I turn on the boiler (water heater)? Procedure

In the modern world, people are used to comfortable conditions and therefore try to create the most comfortable space around them. In order not to worry about interruptions with hot water, many people decide to install a water heater. But because of the rare use of not all know how to turn on a boiler of a particular brand. In fact, this is quite easy and, observing a certain order of actions, the task can be managed independently.

Advantages of the boiler

Hot water in the house is absolutely not a luxury, but a necessary condition for comfort. However, residents of urban flats often face the fact that in summer, hot water is cut off from a centralized supply for repair work. This forces many people to install boilers - tanks that allow heating water and use in the local water supply system.

The advantage of heaters of this type is that they can be installed in almost any, even the smallest room. Modern models consume little power, which saves the family budget. And the most important plus - there will always be a supply of hot water in the house.

Quite simple are such devices in operation, but with occasional use it is possible to forget how to correctly turn on the boiler. The scheme for most models is the same. And subject to a certain sequence of all actions, the water heater will serve its owner for a long time. You can turn it on yourself if you have instructions, or contact a specialist for help.

How do I turn on the boiler?

When it is already installed and connected to the water supply system, it is necessary to make a test run and check the operation of the boiler. In fact, this should not cause any difficulties and the process itself does not require special skills.

First of all, it is necessary to close the centralized hot water supply valve to the apartment. This will prevent the heated water from leaving the common riser. Otherwise, all the residents of the entrance will use the water from the boiler. Manipulation is also carried out if there is a non-return valve.

Practically all models of heaters available on the market (Thermex, Timberk, Electrolux, Ariston and others) are included in the same scheme.

Procedure

How do I turn on the boiler to get hot water? To do this, perform the following steps in the following order:

1. Open the hot water tap on the mixer and make sure it is not there. Close the tap.
2. Open the tap with a blue circle on the inlet of the water heater, then the outlet tap, marked with a red mark. Wait for a while until all the air has left the system, if there was no water in the boiler. Next is the process of filling the water heater.
3. In the event that the boiler was filled with water, it would take only a little to merge it and close the tap with a red circle.
4. Before you turn on the boiler in the socket, it is necessary to completely fill the tank with water. Otherwise, there is a risk of burnout of the tubular heater if the model is not equipped with a protection system.
5. In the process of water heating it is important to monitor the temperature index and supply voltage to the heater.

Experts advise setting the operating temperature regime of the device at the level of 55-60 ° C. This will help to avoid the development of fungi and bacteria in the tank, and also prevent the formation of scale on the heating element.

How do I re-enable hot water?

Boilers are used mainly in the summer period, when often there are interruptions to hot water supply. If the need for heating with a heater has disappeared, it is important to know how to turn off the boiler and turn on hot water from a centralized system. The process may take a little longer than when the unit is connected.

First of all, the appliance is disconnected from the mains. To store the water left in the tank, some experts do not recommend, while others, on the contrary, say that so the parts will be less corroded. If the water still remains in the tank, it must be drained before you turn on the boiler the next time.

It is necessary to cut off the supply of cold water to the heater system (tap with a blue circle). After that, the faucet of the outlet of the heated liquid is closed. The final stage - the inclusion of hot water on the mixer.

Recommendations

Dismantling of the water heater is carried out only after the full discharge of water from the tank. To do this, disconnect the cold water supply hose in the boiler, and in its place, put on the branch pipe, through which the remaining liquid leaves.

In periods when there is no need to operate the boiler, the device is prevented: the heating element is descaled, the presence of a coating inside the tank with a magnesium anode (corrosion protection) is determined. It is best to do this once a year (independently or call a master) in order to extend the life of the water heater.