How do I change the gasket in the tap? Rubber gaskets for the mixer

If in the kitchen or in the bathroom of your house are installed traditional faucets with faucet-bunks, you should be prepared for the fact that after a certain time this element will require repair. Usually, it is accompanied by the replacement of gaskets, which are located between the mixer and the attachment of the crane.

When replacement of the gasket is required

Quite often this procedure is required by cheap mixers. The gasket may require replacement, since it is short-lived, thereby losing its elasticity. On this element may appear cracks and dents, which leads to the fact that even a closed tap starts to leak.

The reasons for the wear of the gaskets are the mistakes made during the repair of the crane, the poor quality of the sealant, and also the water with the content of harmful impurities. Sometimes the gasket is not suitable, since its size was originally chosen incorrectly. Dripping water from the mixer can become an irritant to a person, and plumbing and rust may appear on the plumbing.

Preparation

Before changing the gasket in the tap, it is necessary to collect some warm water in a container. Only after you can close the tap of the water supply system. After the main tap is closed, the water can be drained from the system. Then, using a thick cardboard or a thick towel, you need to cover the surface of the bath or sink, which will prevent damage to the plumbing.

To carry out the work you will need:

• Screwdrivers;
• Fum-tape;
• Adjustable plumbing wrench;
• scissors;
• New gasket.

If a single lever mixer fails, the cartridge inside it can be replaced or a new mixer can be installed. Other types of cranes are quite simple to repair.

Repair of crane-axle boxes with rubber sealant

For valves with rubber seals on sale, you can find Russian and imported gaskets, they are made of silicone and rubber. The standard sizes of the threaded part of the valve can be equal to 1/2 or 3/8 inches. In the store, experts recommend taking mixer parts that are out of order, this will eliminate errors in the selection.

One gasket can be purchased at a price of 3 to 25 rubles. Quite often, home masters are wondering how to make a gasket on the crane-axle. To do this, you can use sheet leather or rubber, in rare cases - dense plastic. The cost of sheet rubber, which is suitable for the manufacture of gaskets, ranges from 150 to 250 rubles. After disassembling the crane and removing the sealant, you can begin the manufacturing process.

On the sheet material, the thickness of which starts from 3.5 mm, you need to make the markings, using the old gasket as a template. The next step is to cut a square piece of material around the perimeter of the markup. After that, the rubber can be trimmed by you more carefully. It is important to ensure the bevel of the edge by 45 °.

Dismantling and repair of crane-axleboxes

When the mixer gaskets have been purchased or completed, you should find plastic decorative plugs on the valves that are dismantled. You can perform these manipulations by tearing the element with a sharp object. The mounting bolt is under the cover, it must be unscrewed with a screwdriver in the next step. At the next stage the lamb is removed from the mixer. A wedge or a wrench will help unscrew the core with the gasket.

Scissors or a sharp knife should hold the gasket in the process of how you will remove it from the rod. Details can be cleaned with warm vinegar, this will get rid of the lime scale. Next comes the turn of the new gasket, if it is made of rubber, then it is installed on the tap of cold water, whereas for the hot water tap the gasket from the skin is suitable. The element must be put on the rod with some effort. If you notice some defects on the core, then it needs to be replaced.

Recommendations of a specialist

In order to facilitate the process, it is recommended to use a certain amount of silicone grease. After the gaskets for the mixer have been installed, you can assemble the tap. The core returns to its place, it is not necessary to twist it too much, then you do not damage the seal. Then the flywheel is installed, and after that the fixing bolt is installed.

Now you can check the efficiency of the crane, for this, it is rotated in different directions. The next step is opening the main valve. Only now you can check if the mixer works correctly. If the repair is not possible to achieve positive results, the rubber gaskets change again. Sometimes it is required and completely replace the mixer.

Replacement of gasket in ceramic faucet

Today ceramic faucets are considered to be one of the most reliable, however even they sometimes fail because water in the water pipe system is of poor quality. For the repair, you can purchase special sets of rubber and ceramic seals, their cost does not exceed 50 rubles. The repair process is quite simple.

At the first stage, remove the decorative plug, unscrew the screw and provide access to the tap by unscrewing the decorative nut. You can remove it with your fingers, sometimes using pliers for this. The crane is twisted and extracted, for this you can also use pliers. They must be directed counter-clockwise, you need to act as carefully as possible, otherwise the thread faces may be damaged.

If you are thinking about the question of how to change the gasket in a ceramic faucet, you need to find a sealing ring that is black. It is advisable to replace the ring with a repair kit. The swivel rod can be disassembled and removed by pressing it with your fingers. Then the stem is easily removed from the body. Rubber ceramic seals change, and they are coated with silicone grease, which allows easier movement of ceramic parts. Reassemble in the reverse order. In order to improve the tightness, before assembling, you must rewind the crane body or the special seal.

Replacement of the gasket in the valve "Geyser"

If you are faced with the problem of how to change the rubber gasket in the tap "Geyser", then to begin it should be dismantled. To do this, the flow control knob is unscrewed, then the outer part is removed. The nut is unscrewed with the metal ring, and then the ceramic steam is removed. At this stage, you can replace the gasket, and then collect everything in the reverse order.

Rubber gaskets are quite easy to find on the market, but some consumers, when replacing them in the geyser crane, face the difficulty of purchasing a ceramic pair. In some cities with such knots in stores a whole problem. However, it is necessary to assemble and disassemble the faucet, observing the accuracy. Otherwise, you may damage the threaded connections.

Replacing the seal in the ball mixer

If you have wondered how to change the gasket in the ball valve, then the technology will not differ too much from those presented above. To carry out the work, it is necessary to prepare the same tools. Work must begin with the removal of the decorative plug, podkovyrnuv her screwdriver. Hexagonal wrench can be unscrewed the locking screw, which fixes the crane lever. The latter should be pulled up and removed from the rod.

The threaded connection is then loosened. It should be hooked with a screwdriver for the notches. If you are thinking about how to change the gasket in the crane, you should remember that all work should be done with care, because otherwise corrugated hoses can be damaged. The pliers will allow you to dismantle the dome with the cuff. Next, the ball is removed from the mechanism.

The seal should be replaced at the next stage, in some cases the ball also needs to be replaced. Specialists recommend replacing springs inside. Further, all parts are installed in place, it is important to observe the accuracy of positioning the ball. With the chrome-dome ring, you can adjust the ease of turning on the crane. Then the lever is fixed, which is fixed with a locking screw.

Conclusion

Before changing the gasket in the faucet, it is necessary to prepare the sanitary lubrication. It will be needed before installing the ball, and its application should be carried out for sealing. This will ensure smooth operation and extend the life of the gaskets. If you are thinking about how to change the gasket in the faucet of a cartridge mixer, you should know that the operation of such a device does not involve the replacement of seals. This is due to the fact that the cartridges are not inseparable.