Why does the washing machine jumping when pressed? Causes of vibration and their elimination

The washing machine for a long time and has firmly entered our life. It significantly reduces the time spent on caring for things, even for those who need a delicate wash. But sometimes there are incidents. For example, the machine starts to jump. Most housewives can not find the reason for this behavior of household appliances. Often these movements of the machine speak of a breakdown, sometimes serious. Why the washing machine jumps when squeezing and how to remove excessive vibrations, this article will tell.

There are quite a few reasons for the strange vibration of the machine. Some problems are easy to diagnose and are eliminated easily. But there are such breakages that require major repairs.

Why the washing machine jumps when pressed: causes

The most frequent breakdowns can be caused by:

• Unstable position due to improper installation (uneven floor, installation is not according to level);
• The imbalance of the laundry loaded into the machine;
• Not removed when installing the machine transport bolts;
• Hit between the drum and the tank machine of small things or parts of the laundry (for example, buttons, bra bones, laundry buttons, rivets);
• Malfunctions of shock absorbers or springs;
• Failure of bearings;
• Broken fastening or total wear of counterweights;
• Damage to the motor.

How to find out why a washing machine jumps when spinning? Troubleshooting is the first thing to do. The reasons for the unhealthy vibration of the machine-machine are many. Diagnosis should begin with the elimination of simple malfunctions, which can be identified by a close examination of the device.

The onset of imbalance

What is the recommended starting point for specialists in determining the cause of mobility of the device? To answer the question, why the washing machine jumps when spinning, you first need to check whether the balance of the drum is broken. This can be indicated by:

• Collapsed after pressing the laundry in a single lump (for example, in a duvet cover).
• For the selected mode, the maximum allowable weight of laundry is not met (authorized loading is indicated in the operating instructions of the device). Not always the maximum calculated load of the washing machine corresponds to a separately taken program.
• Things fill the drum by more than two thirds.

Not removed transport bolts

This is a fairly common reason, explaining why the washing machine jumps when spinning. It occurs when the device is installed independently, without reference to qualified masters. If the machine erases the first time and "went to dance", then with absolute probability, we can say that the installation did not remove the transport bolts.

They are installed at the factory and are designed to ensure reliable fixation of the tank during transportation. The locations of their attachment are described in the attached instructions. Usually there are four.

Non-level setting

There is another common reason why a washing machine jumps when squeezed. To reveal it is simple. You need to swing the car in idle mode. If it easily succumbed, it means that mistakes were made during the installation. This needs to be fixed, preferably using a building level.

Stuck objects between the drum and the laundry tub

Why does the washing machine jumping when pressed, if its installation was done exactly according to the instructions? There is another reason that can be easily corrected. A simple flashlight can help. They need to light up the drum well, gradually scrolling it. Experts easily extract foreign objects stuck deep in the typewriter.

Damage to shock absorbers or springs

A less desirable version of why the washing machine jumps when wringing out is technical reasons. You can not fix them without a specialist. In this case, the vibration will be accompanied by a characteristic knock on the drum's drum, even with a possible grating. The same sounds can be characterized by the wear of the counterweight weights or of it.

This fault can be diagnosed by yourself. To do this, remove the cover of the machine and check the described elements. If they are fit, then there are two reasons for the jumps in the unit.

Damage to the motor or manufacturer's fault

So, you've already looked at everything, but still have not figured out why the washing machine jumps when squeezing? Technical malfunctions of the "heart" of the device or an error in its release may be the main cause of the failure. It should be recalled that household appliances, which did not have a warranty period, can not be opened independently. To fix all the problems you need to contact the warranty workshop or the store where the equipment was bought.

Troubleshooting at home

In most cases, the cause of the problem is easily removable. First of all, you need to decide where to put the device and how to fix it. If the washing machine jumps when squeezing, you should clearly adhere to the algorithm of actions to eliminate this trouble. When the device vibrates due to a simple unbalance, the actions can be as follows:

• Turn off the washing mode and turn off the machine from the mains;
• It is necessary to open the door of the machine, and if this can not be done, it is necessary to make an emergency drain of water;
• After unlocking the door, release the drum from the laundry;
• It is recommended to lay half of the extracted laundry (straightened and no more than 2/3);
• Close the machine door and start the appropriate mode.

If the cause of the vibration is incorrect installation, then you need:

• To dismantle the automatic machine, preliminary having disconnected from an electricity, a waterpipe and the water drain;
• Carefully level the surface occupied by the machine, preferably using a building level;
• Install the device in place and now, by scrolling the legs on the level, adjust the horizontal;
• In the case of a slippery floor surface, put anti-slip or anti-vibration mats under the machine.

If the cause of unhealthy vibration is a jammed object, you can try to pull it out yourself by hooking something. In case of failure it is necessary to call a specialist, since the machine will have to be dismantled almost to the ground.

Used springs or shock absorbers must be changed. They are not subject to repair. It is only necessary to take into account that even if one of the shock absorbers is defective, both must be replaced , since the load should be distributed evenly. If you have the skills to work with different tools and the experience of using it, you can find a scheme for the upcoming work in professional journals and act independently. Otherwise, you need to contact the firm for repair of home appliances and entrust this work to the master. In the same scenario, it is necessary to act if the bearings are broken. By the way, they have a service life of no more than 5-6 years.

If the machine jumps due to a malfunction of the counterweight, the following steps must be taken.

Depending on the brand and model of the machine with a screwdriver, pliers or keys, you need to remove the top cover and inspect the counterweight. This is a special weighting agent, which is usually made of concrete or cast iron. The second half is almost above the floor. If the weights of the weights are loosened, tighten them. In case of failure, they must be replaced. If the concrete weighting agent itself is deformed, it can also be changed to a similar one.

And, of course, if the vibration is caused by a breakdown of the electric motor, then there is no way to do without a specialist. Consultation with him will help to decide whether the machine is repairable or you need to purchase a new one.

Interesting nuances

It is necessary, of course, to take into account that all machines are slightly vibrating. These are the eternal laws of physics. But this technique has its own laws. For example, it is noted that narrow machines are more susceptible to vibration than devices of standard width. This is easily explained: the area of the support of the narrowed machine is less, hence, and its stability will be poor, whence there is an excessive vibration. Plus, in these devices there are special narrowed drums, in them the laundry is easier to get into a ball, which unbalances the work and also leads to vibration. Under these machines necessarily lay anti-slip or anti-vibration mats. They quench excessive vibration.

Before buying a machine you need to consult a specialist of the outlet and find out what material the laundry tank is made from. For example, metal containers are very loud in operation, especially when spinning. While plastic-made drums are considered more stable and quiet. And absolutely modern machines with linen tanks that do not come into contact with the hull operate silently.