How to fill the ink seal correctly

In a modern office, old-fashioned stamps and pads have replaced ergonomic automatic prints. Sometimes they are called traders - by the name of a well-known company that produces equipment for them. With regular use of the automatic trader, the ink on the cushion dries out, and the stamp imprint on the paper becomes pale and indistinct. Documents with pale prints do not yield to photocopying and scanning. The legal departments of many companies can recognize such papers as invalid.

If in the office there was a need to fill a stamp pad, it is not necessary to call specialized companies to learn how to fill the seal with ink. The instructions for refueling are usually available in special boxes, in which automatic rigging is sold. The standard recommendation is to buy a new ink pad for printing. But this advice can be quite expensive for a company. So let's try to find out how to fill the seal with ink, without damaging it, and do not get dirty.

How to remove a stamp pad

In standard automatic printing, the ink pad is in the middle. It can be seen from the side. A photo of the automatic printing with the position of the stamp pad is located below.

To understand how to fill a round seal with ink, you need to pull out this pad. For this, you need to press the two buttons located on the sides of the trader, while slightly pressing down the print. If everything is done correctly and the automatic rig has not been damaged, the buttons will fix a slightly pressed state. After this, using an ordinary pencil, you should gently pull the pad from the side gap.

How to prepare a seal for a gas station

Before you fill the seal with ink, you should clean the removed cushion and remove from it the sticky lumps of paint, pieces of paper and other possible contaminants. Different dents left on a soft surface, it makes sense to smooth a nongty-sized object. For this purpose, an ordinary clerical clip will perfectly fit. The end of it is carefully leveled out all the impressions. A worn pad is not elastic, it practically does not absorb ink, it shows deep dents that can not be smoothed out. It makes no sense to impregnate a pad with ink stamps, it is better to order a new one - and then you will not need to learn how to fill the seal with ink. The photo of the removed pads can be viewed below.

How to apply ink stamps

Thus, the print cushion is prepared for staining with ink. The required paint is produced by various companies, including in our country. In no case should you fill the seal with ink or other liquids - you can quickly and hopelessly spoil it. The standard bottle of ink has a dispenser, which is very convenient to drip paint on the print.

A few drops of ink should be gently and evenly applied to the surface of the pillow. Surplus can be removed with a napkin. After painting, wait a few minutes for the liquid to soak into the surface. We insert a small pillow in an equipment for printing by ink side downwards. To answer the question of how to properly fill ink with ink, if two or three colors are used in automatic printing, you simply need to consistently pull out the pads of different colors and fill them with appropriate ink stamps. The sequence of actions is the same as with single-color seals.

Flash Printing

Recently, a new type of print is widely distributed - flash printing. From the usual stamp they differ in that their working surface, which is applied to the print, is absolutely smooth. In this printing, several colors are used, it is more accurately and uniformly applied to the paper. Flash printing is much more durable, and the level of protection they have an order of magnitude higher.

Filling single-color flash printing

Despite the durability and durability, after a while there is still a question about how to fill the seal with ink. In order to quickly fill up flash printing in a simple way, you need to have a syringe and a suitable ink on hand. The cliché is located on the cushion pad. We remove the cliche and put it on a flat surface. Paint evenly several times using a syringe. Between applications, you should wait for a while, so that the ink is evenly absorbed in the cliche. The layer of applied liquid should not exceed 2 mm. We let the ink absorb completely, wipe off the excess ink deposited with a napkin and collect the seal in its original state.

Filling multicolor flash printing

When refilling a multicolor flash, you need to get a cliche like the one described above. This part is filled with syringes, and care must be taken to ensure that the colors do not mix. Paints of different colors have different degrees of fluidity. Remember how to fill the seal with ink, it's easy: first, paint is applied to one print segment, then to another. When refueling for each color you need to use a separate syringe, otherwise the colors will be dirty and blurry. After the procedure for filling the ink with a cliche, the flash print should be put aside. The paint should spread evenly over the surface, this takes some time. After that, we paste the cliché into place and try the prints.