Attachments for motoblock own hands. Drawings, assembly instructions

If you have a plot of land, you are familiar with how difficult it is to work on digging, loosening and hilling. This takes a lot of time and energy. In order to facilitate the solution of such problems, it is possible to purchase auxiliary special equipment, it can be performed by a motoblock. Using this equipment, you can perform a wide range of works. This can be the processing of land, cleaning the site, as well as transporting the crop and any other cargo.

Solution

Remove the snow, weed and weed it is impossible without attachments, it is available for sale in a wide range, among other options should be allocated adapter, which is a trolley with a seat. This addition turns an ordinary motoblock into a real tractor, but in stores it is quite expensive. Therefore, you can make the adapter yourself, as well as some other types of attachments.

Instructions for assembling a simple adapter for a motor block

Attachments for the motor block with their own hands can be made almost to any home masters. If you want to manufacture an adapter, it can be a steel frame made of a pipe. To do this, you need to take one that has a rectangular section, while the length should be 1.7 m.

One of the ends perpendicularly needs to weld a pipe, the length of which is 0.5 m. This part will become the basis for fixing the racks for the wheels. The height of the racks from the axis to the top point will be 0.3 m. In the next step, you must fix the braces to the central pipe and the wheel hub. The length of the products will depend on the inclination and angle.

A square frame can be any size. In this example, the following dimensions will be considered: 0,4 x 0,4 m. If you decided to make such hinged equipment for the motor block with your own hands, then the channel should be strengthened to the rear end of the frame, the length of which is 0.4 m. Collect the side pipes in A single construction can be done with bolts. To be able to adjust to the frame, the lever must be welded, which must have three elbows, their length being the following: 20, 30 and 50 cm respectively. In order to increase the applied forces, the lever should be supplemented with a 75-cm lever. The coupler can be purchased or manufactured independently. From the quality of the hitch will depend on the duration of operation of attachments. On the metal support it is necessary to fix the seat, which is welded to the central pipe. On this you can assume that you managed to make attachments for the motor block with your own hands. Its advantages are low price and simplicity of design.

Recommendations for the implementation of the coupling unit

If you decide to implement the attachments for the motoblock with your own hands, you should become more familiar with the instructions for making the coupling unit. The simplest design is a 15-centimeter pin, which is installed in the hole of the drawbar of the towbar of the motor-block. As a disadvantage of this option is a fairly rapid wear, because under the influence of a rotating trailer, the holes for the coupling are broken. In order to reduce the rate of wear, the coupling can be extended.

Recommendations for mounting the seat

Drawings of attachments for motoblock can be made independently. Of these, you can find out that the adapter is attached to the equipment using a single hitch, which consists of two parts. The first is required to connect the equipment, while the other is an adjustable adapter between the equipment and the lifting mechanism.

To increase the number of used tools, the adapter can be supplemented with a universal double hitch. Such equipment for motoblock "Salute" is also suitable. However, for familiarization with the instruction it is important to ask how the installation of the seat is carried out. With a ledge 80 cm from the front edge of the spinal frame, you need to fix the seat. Use with this you need bolts. After the entire system is assembled, it must be checked for operability.

Plowing

Before making this attachments, it is necessary to prepare the drawings. In them you will be able to identify the main nodes - the share and the blade. For working elements, 3 mm steel should be used, however, for the beginning experts advise working on a removable share. As the most suitable material for him to make a disk, borrowed from a circular saw. In the absence of it, you can use ordinary steel, which was not subjected to heat treatment.

The cutting part is the working element of the braid, which fights on the anvil. The plow hinged must have a blade in the structure, you can start making it after you have finished with the ploughshare. As material for this, a 50 mm pipe with a thickness of 5 mm can be used. The blade can be made using a gas cutter. To start, the template is cut out, in the next step the workpiece can be brought to the anvil, and then - on the grinder.

Plow Assembly

Hinged homemade equipment at the next stage can be put together. To begin with, you should use the option of assembling the layout, which is made of thick cardboard. The parts are glued together, and you need to adhere to the necessary angles. After finishing the blade, plowshare and auxiliary parts, you can prepare a steel 2 mm square sheet with a side of 500 mm. From the edges, an indentation of 40 mm is made, then a share is applied and spot welding is done from both sides.

The rack post should also be joined with a share, the joint must pass in an upright position. The shield should be placed somewhat higher compared to the blades of the share. Indentation is necessary to crop the soil. It is important to densely join the shares with the blade, there should not be any gaps. The design in the end should be almost cast. Between the upper edge of the shaft and the blade of the share, it is necessary to set the angle in the range from 6 to 8 ° C.

Mower Manufacturing

A mower for a motoblock with your own hands can also be performed. It is used for lawn care, mowing grass for hay. For work, it is necessary to prepare chains from a chainsaw gearbox, as well as a pair of disks borrowed from a grain drill. Knives can be made from hardened metal, 4 blades are needed for each disk. Drives should be drilled holes, the diameter of which is 6 mm. On the disk, the knives should be reinforced using tines. The clearance between the knife and the shank by 2 mm should be greater than the thickness of the knife.

When a mower for a motoblock is made by one's own hands, the axes of fastening the knives can be made of carbonaceous strong steel, the diameter of which is 8 mm or more. The axle must be tightened against the disc until it stops, so as not to impede the movement of the blades.

Conclusion

On the welded frame, you should fix the discs and tie up with the drive - additional handles on the motor block construction. Gears can be borrowed from the car VAZ. Disks should rotate towards each other, this will allow the mown grass to fit into the rows. A protective cover can be fitted to the actuator.