Washing machine does not drain water: the reason and the algorithm of actions

Washing machines are so firmly in a couple of decades have entered our lives that the sudden breakdown of this unit badly spoils the mood and violates plans. Wash by hand, it turns out, is very tiring and long. And wring out the laundered laundry as carefully as smart technology does, and it's completely unreal. Here, perhaps, the most common complaint: the washing machine does not drain the water. The reason for this may be not even one, but several. Surely many face sooner or later with a similar problem. And they want to understand why the washing machine does not drain the water. An overview of possible causes is given below.

Electronics failure

If household appliances stumbled halfway, that is, the washing cycle or rinsing cycle for all parameters should be finished, but the washing machine does not drain the water - what should I do in this case? At the very least, clarify whether the program on which such a nuisance happened really involves draining the water and squeezing it, and if so, it could be due to all the fault in the electronics of the device. This can happen, given the instability of the voltage in the domestic electricity network. The first thing to do is to reset the machine. Simply put: turn off the plug from the outlet and turn it on again. If this does not help, you can re-select the rinse and spin program, already using the buttons. In the absence of any effect, the cause will have to be looked for further.

Checking the hose, through which the drain is carried out

In circumstances characterized by the fact that the washing machine does not drain water, the reason may be the simplest. It may be that the drain hose is simply pinched, twisted or incorrectly installed. With this, in fact, and need to start - to exclude the most obvious reason for disrupting the work of household appliances. It is enough to trace the position of the hose all along its length, straighten it and at the same time check for the presence of blockages inside, and also to check the requirement that the height of its inflection should be sufficient. As a rule, its minimum value is 60 cm from the bottom edge of the machine. If the sink is organized into a sewer pipe, the problem may be in the clogging of the siphon. It is necessary to remove the drain hose and lower it into the tub or basin. If the sink is working - you have to clean the sewer.

Clogged filter

Making sure that the drain hose is not at all the main culprit to the fact that the washing machine does not drain the water, the reasons must be searched further inside the machine, namely, in the clogging of the filter with which the drain pump is equipped. This part is located most often on the front panel under the tank, and you can get to it by removing the cover. To open it, you may need a flat screwdriver or a knife - it depends on the model. By removing the cover, you can not only remove and, if necessary, clean the water pump filter.

You can also drain the water from the tank of the machine through a short drain pipe located in the same place as the filter. So in advance, take care of the container with low sides or a few dense rags, so that the water does not pour into a vast puddle on the floor. As for the filter itself, it can be clogged with pile from clothing, buttons, coins, hair, threads, peanuts from seeds or nuts and other small items that get into the washing machine with clothes. The filter is usually equipped with a handle, by means of which it is twisted, and at times rather tight, as it is sealed with a rubber gasket.

The clogging can be so strong that it will not be possible to unscrew the filter on its own, but the specialist is on the shoulder. By the way, in some cheap models the filterwashers may not be at all.

Under the circumstances listed above, in connection with which the washing machine does not drain water, repair by one's own hands is quite possible. To reboot the program, straighten the drain hose or pull out and clean the filter, special skills are not needed. Moreover, the preventive cleaning of the pump filter must be carried out at least once every five years, without waiting for it to be reminiscent of the formed clog, which caused a malfunction in the machine. This procedure, as a rule, is described in detail in the instructions to the typewriter. If the hose and filter are checked and in order, but it did not change anything, and the washing machine does not drain the water, what should I do next? Further it will be already more difficult. I'll have to get to the branch pipe, which connects the pump to the tank of the washing machine.

Necessity of nozzle cleaning

If the owner of the washing machine is not sure that he can find and get this part - will have to contact the masters. The craftsmen will be able to check the branch pipe for a blockage and collect all the construction back without damaging the equipment. If the nozzle is clean, but the problem has not resolved it and the washing machine still does not drain the water, the reason may be in the jamming of the pump impeller, or the pump, for pumping out the water.

Checking the pump impeller

It's quite simple. The impeller of the pump is located immediately behind the filter. After removing the filter, it is visible in the hole. You can just try to unscrew its blades by hand, and if it rotates with difficulty - remove what prevents it from spinning. If no foreign object interferes with it, but nevertheless, when it is squeezed, it does not rotate and the washing machine does not drain the water, the reasons must obviously be found in the pump itself.

Problems with the pump: wear or breakage

It is possible to buy a new pump and replace it with an old, broken one, but if the washing machine is under warranty, then it's better not to take risks. For the service center this task will be quite ordinary. It is the consequence of problems with the drain pump that happens most often that the washing machine does not drain the water. The reason lies, as a rule, in wear, breakage or industrial fault in the pump design. Usually the pump does not break down overnight, this is preceded by multiple failures in her work and the strange sounds she makes.

Other reasons

If all of the above problems are eliminated, and the washing machine refuses to end the washing or rinsing process, drain the water and go into spin mode, the problem may be in the failure of the device's electronic card or in violation of the internal wiring of the machine. Do this yourself is not exactly right, you need to contact a specialist for diagnosis. It may be necessary to reflash the electronic module or replace it completely. To restore the integrity of the wires of the washing machine, too, some knowledge is needed.

conclusions

So, the article discusses the main reasons for such a common problem as the failure of a washing machine in the process or after washing to drain the water and begin to spin. This can be as a malfunction in the electronic command device, and clogging the filter or sewer, the wear of the pump or simply the installation error of the drain hose. Sometimes a malfunction can easily be resolved, but in many cases the help of masters will be needed. Having decided to eliminate the breakdown yourself, it is necessary to understand that in case of inadequate actions, the repair of the unit can cost even more. Now, if the washing machine does not drain the water, what to do - in general terms it should be clear.